31
5
Lower the buttonhole lever and push it back
slightly.
6
While gently holding the upper thread, start
the machine.
7
The bar tacks of the buttonhole are sewn in
the order shown.
8
Stop the machine when buttonhole stitching is
finished.
■ Making a Buttonhole on Stretch Fabrics
When sewing buttonholes on stretch fabric, the
buttonhole stitching is sewn over a gimp thread.
1
Using tailor’s chalk, mark the position of the
buttonhole on the fabric, and then attach the
buttonhole foot and set the pattern selection
dial to “ ”.
2
Hook the gimp thread onto the back end of
the buttonhole foot, bring the two gimp
thread ends to the front of the foot, insert
them into the grooves, and then temporarily
tie them there.
3
Lower the presser foot and start sewing.
*Set the stitch width to match the diameter of
the gimp thread.
4
Once sewing is completed, gently pull the
gimp thread to remove any slack, and then
trim off the excess.
Making a Buttonhole
(4-Step Buttonhole)
Memo
● We recommend that you practice making a
buttonhole on a scrap piece of fabric before
you try it on the actual garment.
● When making buttonholes on soft fabrics,
place stabilizer material on the underside of
the fabric.
Making a buttonhole is a simple process that
provides reliable results.
■ Making a Buttonhole
1
Using tailor’s chalk, mark the position and
length of the buttonhole on the fabric.
2
Attach the buttonhole foot, and then slide the
outside frame of the buttonhole foot as far
back as possible.
PUSH
1
3
2
4
Pattern
Stitch Length
[mm (inch)]
Stitch
Width
[mm (inch)]
Foot
(4-Step
Buttonhole)
-1.5
(1/64-1/16)
3-5
(1/8-3/16)
Buttonhole
Foot
PUSH
PUSH
E<=
Four-Step
Buttonholing
The four dial settings for buttonholing are
located on the stitch length selector. As you
turn the dial for each step, your machine is
automatically
set
for
the
correct
needle
position, stitch width, and stitch length, as well
as for stitching direction for that step. You
jjee^jTO^turTWhe^fabri^duri^
•
Pattern: Zig-Zag
• General Purpose Needle Plate
•
Buttonhole Foot
Preparation
• Prepare and mark
instructed on page 67.
your garment, as
•
Position work under needle, aligning centre
marking of buttonhole with centre line on
the foot. Align end marking of buttonhole
with the horizontal lines on the foot.
•
Set the buttonhole balance knobK in neutral
position,
as
ilustrated.
The
buttonhole
balance Knob, when turned slightly to the
right or left, enables your to balance the
stitch
density
of
both
sides
of
the
buttonhole Refer to the next page for
information on balancing buttonhole stitch
density.
Step 1 ‘.Side Stitching
Raise needle above the fabric and turn the
buttonhole dial to stepl. Position needle in
fabric at pointA. Lower the foot and stitch to
end of buttonhole (point B). The end marking
shoud be aligned with the horizontal lines on
the foot.
Step 2:Bar Tack
Raise the needle out of the Tabric. Turn
buttonhole dial to step
2
and take at least four
stitches. Stop at point C.
Step 3:Side Stitching
Raise the needle out of the fabric. Turn
buttonhole dial to step 3. Complete work to
pointD. Raise needle.
Step 4:Bar Tack
Raise the needle out of the fabric and turn
buttonhole dial to step 4. Take at least four
stitches ending at point E. For a smooth, satin
appearance and greater durability, stitch around
the buttonhole a second time by rebeating the
four-step sequence.
——————— 71-^
If your four step buttonhole symbols are located on the stitch length dial on the front of your machine read the Manual instructions or watch this VIDEO
If your four step buttonhole symbols are located on the pattern selector of your machine read the Automatic Instructions.
4-Step Manual Buttonholes
Preparation: Measure the diameter and thickness of your chosen button and add 1/8″ for bar tacks and mark the button hole size on the fabric.
Figures 1 & 2:
1. Raise the presser foot.
2. Place the fabric under the foot.
3. Center three red guidelines (refer Figure 1) of the buttonhole foot around the beginning line of the buttonhole.
4. Turn the buttonhole dial to the button symbol «1» for the first step.
5. Position the needle in the fabric at point #2 by turning the handwheel towards you.
6. Stitch down to point #3. Your buttonhole should appear as shown in Figure 2.
Figure 3:
1. Raise the needle out of the fabric.
2.Turn the buttonhole dial to the buttonhole symbol «2» for the second step.
3. Make at least four stitches, ending at point #4
Figure 4:
1. Raise the needle out of the fabric.
2. Turn the buttonhole dial to the buttonhole symbol «3» for the third step.
3. Stitch up to point #5.
Figure 5:
1. Raise the needle out of the fabric.
2. Turn the buttonhole dial to the buttonhole symbol for «4» for the fourth/last step.
3. Make at least 4 stitches, ending at point #6.
4. Raise the presser foot and remove the garment from the machine.
5. Clip thread ends.
6. To open the buttonhole insert a seam ripper from both ends towards the middle.
4-Step Automatic Buttonhole
Preparation: Measure the Diameter and thickness of your chosen button and add 1/8″ for bar tacks and mark the buttonhole size on the fabric.
- Remove the General Purpose presser foot from your machine and attach your Buttonhole presser foot.
- Place your fabric under the foot so the markings on the Buttonhole presser foot align with your markings on the fabric.
- Adjust the stitch length dial to 0.5 — 1 to set the density. Note: Density varies according to the fabric. Always sew a test buttonhole first.
- Follow the 4-step sequence changing from one step to another with the stitch pattern selector dial. Take care not to sew too many stitches in steps in 1 and 3.
- Insert a seam ripper to open the buttonhole from both ends towards the middle.
Tips:
- Reduce the upper thread tension slightly for better results.
- Use a backing for fine or stretchy fabrics.
- It is advisable to use heavy thread or cord for stretch knit fabrics.
17
Sew 4-step Buttonholes
Prepare
Note:
Tips:
1. Take off the all purpose foot and attach the buttonhole foot.
2. Measure diameter and thickness of button and add 0.3cm
(1/8″) for bartacks to obtain correct buttonhole length; mark
buttonhole size on fabric (a).
3. Place fabric under the foot, so that marking on the
buttonhole foot aligns with starting marking on fabric. Lower
the foot, so that the buttonhole center line marked on the
fabric aligns with the center of the buttonhole foot
.
Density varies according to the fabric.
Always test sew a buttonhole on the fabric you are using
to sew the buttonhole.
Follow the 4-step sequence changing from one step to
another with the Pattern Selector Dial. When moving from
step to step through the buttonhole process, be sure that the
needle is raised before turning the Pattern Selector Dial to
the next step. Take care not to sew too many stitches in
steps 1 and 3. Use seam ripper and cut buttonhole open
from both ends towards the middle.
— Slightly reducing upper thread tension will produce better
results.
— Use a stabilizer for fine or stretchy fabrics.
— It is advisable to use heavy thread or cord for stretch or
knit fabrics. The zig-zag should sew over the heavy thread
or cord. (A)
(b)
Adjust the Stitch Length Dial (model 1409 only) in the «
«
range to set stitch density.
A
1
3
4
2
Model 1409 only
2
3
1
4
2
4
3
1
(a) (b)
17
Sew 4-step Buttonholes
Prepare
Note:
Tips:
1. Take off the all purpose foot and attach the buttonhole foot.
2. Measure diameter and thickness of button and add 0.3cm
(1/8″) for bartacks to obtain correct buttonhole length; mark
buttonhole size on fabric (a).
3. Place fabric under the foot, so that marking on the
buttonhole foot aligns with starting marking on fabric. Lower
the foot, so that the buttonhole center line marked on the
fabric aligns with the center of the buttonhole foot
.
Density varies according to the fabric.
Always test sew a buttonhole on the fabric you are using
to sew the buttonhole.
Follow the 4-step sequence changing from one step to
another with the Pattern Selector Dial. When moving from
step to step through the buttonhole process, be sure that the
needle is raised before turning the Pattern Selector Dial to
the next step. Take care not to sew too many stitches in
steps 1 and 3. Use seam ripper and cut buttonhole open
from both ends towards the middle.
— Slightly reducing upper thread tension will produce better
results.
— Use a stabilizer for fine or stretchy fabrics.
— It is advisable to use heavy thread or cord for stretch or
knit fabrics. The zig-zag should sew over the heavy thread
or cord. (A)
(b)
Adjust the Stitch Length Dial (model 1409 only) in the «
«
range to set stitch density.
A
1
3
4
2
Model 1409 only
2
3
1
4
2
4
3
1
(a) (b)
20
2
1
4
3
A
D
a
b
E
B
C
Buttonhole sewing is a simple process that provides reliable
results. However, it is strongly suggested to always make a
practice buttonhole on a sample of your fabric and stabilizer.
Making a Buttonhole
Making a Buttonhole on Stretch Fabrics (E)
1. Using tailor’s chalk, mark the position of the buttonhole on the
fabric.
2. Attach the buttonhole foot and set the Pattern Selector Dial to «
«.
Set stitch length dial to «
«. Set the stitch width at «6». The
width however may need to be adjusted according to the
project. Sew a test first to determine this.
3. Lower the presser foot aligning the marks on foot with the
marks on the fabric (A). (The front bar tack will be sewn first.)
(Align the mark on the fabric (a) with the mark on the foot (b).)
4. Open the button plate and insert the button (B).
5. Lower the buttonhole lever and gently push it back (C).
6. While lightly holding the upper thread, start the machine.
7. Buttonhole stitching is done in the order (D).
8. Stop the machine when the buttonhole cycle has completed.
When sewing buttonholes on stretch fabric, hook heavy thread or
cord under the buttonhole foot. When the buttonhole is sewn the
legs will overcast the cord.
1. Mark the position of the buttonhole on the fabric with the
tailor’s chalk, attach the buttonhole foot, and set the pattern
selector dial to «
«. Set stitch length dial to «
«.
2. Hook the heavy thread onto the back end of the buttonhole foot,
then bring the two heavy thread ends to the front of the foot,
insert them into the grooves and temporarily tie them there.
3. Lower the presser foot and start sewing.
*Set the stitch width to match the diameter of the gimp thread.
4. Once sewing is completed, gently pull the heavy thread to
remove any slack, then trim off the excess.
PUS
H
PUSH
M
Sew 1-step Buttonholes
31
5
Lower the buttonhole lever and push it back
slightly.
6
While gently holding the upper thread, start
the machine.
7
The bar tacks of the buttonhole are sewn in
the order shown.
8
Stop the machine when buttonhole stitching is
finished.
■ Making a Buttonhole on Stretch Fabrics
When sewing buttonholes on stretch fabric, the
buttonhole stitching is sewn over a gimp thread.
1
Using tailor’s chalk, mark the position of the
buttonhole on the fabric, and then attach the
buttonhole foot and set the pattern selection
dial to “ ”.
2
Hook the gimp thread onto the back end of
the buttonhole foot, bring the two gimp
thread ends to the front of the foot, insert
them into the grooves, and then temporarily
tie them there.
3
Lower the presser foot and start sewing.
*Set the stitch width to match the diameter of
the gimp thread.
4
Once sewing is completed, gently pull the
gimp thread to remove any slack, and then
trim off the excess.
Making a Buttonhole
(4-Step Buttonhole)
Memo
● We recommend that you practice making a
buttonhole on a scrap piece of fabric before
you try it on the actual garment.
● When making buttonholes on soft fabrics,
place stabilizer material on the underside of
the fabric.
Making a buttonhole is a simple process that
provides reliable results.
■ Making a Buttonhole
1
Using tailor’s chalk, mark the position and
length of the buttonhole on the fabric.
2
Attach the buttonhole foot, and then slide the
outside frame of the buttonhole foot as far
back as possible.
PUSH
1
3
2
4
Pattern
Stitch Length
[mm (inch)]
Stitch
Width
[mm (inch)]
Foot
(4-Step
Buttonhole)
-1.5
(1/64-1/16)
3-5
(1/8-3/16)
Buttonhole
Foot
PUSH
PUSH
5
ПРИНАДЛЕЖНОСТИ
1 Лапка для выметывания петель (1 шт.)
2 Лапка для вшивания застежки “молния” (1 шт.)
3 Лапка для пришивания пуговиц (1 шт.)
4 Набор игл (обычная одиночная игла HAX130) (3 шт.)
5 Двойная игла (1 шт.)
6 Шпульки (3 шт.)
7 Отвертка (1 шт.)
8 Дополнительный стержень для катушки (1 шт.)
9 Штопальная пластина (1 шт.) (Когда машина не
оснащена переключателем положения гребенок
транспортера.)
Код изделия для прижимной лапки для строчки
“зигзаг”: 138135C122
Педаль:
XC7359C021 (110/120 В)
XC7438C021 (220/240 В)
Перечисленные выше принадлежности хранятся в
специально предназначенном для них футляре
внутри столикаCприставки. Эти принадлежности
предназначены для облегчения выполнения
большинства швейных задач.
2 X59370-021
8 130920-021
3 X59375-121
4 129583-001
5 X57521-001
6 SA156(For U.S.A.)
SFB(XA5539-151)(For other countries)
7 X55467-021
9 XA3442-121
1
XA4911-151
X59369-321
(For 1 Step Automatic Buttonhole)
(For 4 Step Buttonhole)
XL5050ru.book Page 5 Wednesday, August 24, 2005 5:52 PM
1408 / 1409 Instruction Manual
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety should always be followed, including the following: Read all instructions before using this sewing machine. DANGER — To reduce the risk of electric shock: 1. An appliance should never be left unattended when plugged in.
Congratulations As the owner of a new Singer sewing machine, you are about to begin an exciting adventure in creativity. From the moment you first use your machine, you will know you are sewing on one of the easiest to use sewing machines ever made. May we recommend that, before you start to use
List of Contents Machine Basics Principle Parts of the Machine…………………………………………………………………………………………………………………………….2/3 Connecting Machine to Power Source
Principal Parts of the Machine 1. Thread tension dial 2. Thread take-up lever 3. Thread cutter 4. Face plate 5. Presser foot 6. Needle plate 7. Removable extension table/ accessory storage 8. Pattern selector dial 9. Bobbin stopper 10. Stitch length dial (Model 1409) 11. Reverse sewing lever 2
Principal Parts of the Machine 12. Handle 13. Bobbin winding spindle 14. Spool pins 15. Handwheel 16. Power and light switch 17. Main plug socket 18. Bobbin thread guide 19. Presser foot lifter 20. Foot speed control 21. Power cord 3
Connecting Machine to Power Source Connect the machine to a power source as illustrated. (1) This appliance is equipped with a polarized plug which must be used with the appropriate polarized outlet. (2) A Attention: Unplug power cord when machine is not in use. Foot control The foot control pedal
Two Step Presser Foot Lifter When sewing several layers or thick fabrics, the presser foot can be raised to a higher position for easy positioning of the work. (A) A 5
Accessories Standard accessories (1) a. All purpose foot b. Zipper foot c. Buttonhole foot d. Button sewing foot e. L-screwdriver f. Seam ripper/ brush g. Spool pin felt (2x) h. Pack of needles (3x) i. Edge/ quilting guide j. Bobbin (3x) k. Darning plate 1 Standard accessories Optional accessories
Winding the Bobbin — Place the thread and Spool pin felt (a) onto the spool pin. (1) — Wind thread clockwise around bobbin winder tension discs. (2) — Thread bobbin as illustrated and place on spindle. (3) — Push bobbin spindle to right. (4) — Hold thread end. (5) — Step on foot control pedal. (6)
Inserting the Bobbin When inserting or removing the bobbin, the needle must be fully raised. 1. Open the hinged cover. 2. Pull the bobbin case tab (a) and remove the bobbin case. 3. Hold the bobbin case with one hand. Insert the bobbin so that the thread runs in a clockwise direction (arrow). 4.
Threading the Upper Thread This is a simple operation but it is important to carry out correctly as by not doing so several sewing problems could result. — Start by raising the needle to its highest point (1), and continue turning the handwheel counterclockwise until the needle just slightly begins
Raising the Bobbin Thread Hold the upper thread with the left hand. Turn the handwheel (1) towards you (counterclockwise) lowering, then raising needle. Note: If it is difficult to raise the bobbin thread, check to make sure the thread is not trapped by the hinged cover or the Removable Extension
Thread Tension Upper thread tension Basic thread tension setting: «4». (1) To increase the tension, turn the dial to the next number up. To reduce the tension, turn the dial to the next number down. A. Normal thread tension for straight stitch sewing. B. Thread tension too loose for straight stitch
How to Choose Your Pattern To select a stitch, simply turn the pattern selector dial (a). The pattern selector dial may be turned in either direction. The following page shows the recommended range of stitch lengths. a b Adjust the stitch length with the stitch length dial (b) according to the
Stitch Length Dial (Model 1409 only) Function of stitch length dial for when straight stitching For straight stitch sewing, turn the Pattern Selector Dial to the straight stitch setting. (1) Turn the Stitch Length Dial, and the length of the individual stitches will decrease as the dial approaches
Sewing Straight Stitch To begin sewing, set the machine for straight stitch. (1) Place the fabric under the presser foot with the fabric edge lined up with the desired seam guide line on the needle plate. (2) Lower the presser foot lifter, and then step on the foot controller to start sewing. (3) 1
Reverse Sewing To secure the beginning and the end of a seam, press down the reverse sewing lever (A). Sew a few reverse stitches. Release the lever and the machine will sew forward again. (1) A Removing the Work Turn the handwheel toward you (counterclockwise) to bring the thread take up lever to
Blind Hem For hems, curtains, trousers, skirts, etc. Blind hem for stretch fabrics. Blind hem/ lingerie for firm fabrics. Note: It takes practice to sew blind hems. Always make a sewing test first. Model 1409 only Blind Hem: Turn up the hem to the desired width and press. Fold back (as shown in
Sew 4-step Buttonholes Prepare 1. Take off the all purpose foot and attach the buttonhole foot. 2. Measure diameter and thickness of button and add 0.3cm (1/8″) for bartacks to obtain correct buttonhole length; mark buttonhole size on fabric (a). 3. Place fabric under the foot, so that marking on
Sewing on Buttons (Model 1408 only) Install the darning plate. (1) Change the all purpose foot to button sewing foot. (2) Position the work under the foot. Place the button in the desired position and lower the foot. Set the Pattern Selector Dial for the second zig-zag pattern (as shown), which
Sewing on Buttons (Model 1409 only) Install the darning plate. (1) Change the all purpose foot to button sewing foot. (2) Position the work under the foot. Place the button in the desired position and lower the foot. Set the Pattern Selector Dial on » » and sew a few securing stitches. Select one
Free Motion Darning, Stippling * The darning/ embroidery foot is an optional accessory not included with your machine. (1) Darning: Install the darning plate. (2) Remove the presser foot shank. (3) Attach the darning/ embroidery foot to the presser foot bar. The lever (a) should be behind the
Installing the Removable Extension Table Hold the removable extension table horizontally, and push it in the direction of the arrow. (1) To remove the extension table, pull it toward the left. 1 The inside of the removable extension table can be utilized as an accessory box. 2 21
Attaching the Presser Foot Shank Raise the presser foot bar (a) with the presser foot lifter. Attach the presser foot shank (b) as illustrated. (1) a a Attaching the presser foot Lower the presser foot shank (b) using the presser foot lifter, until the cut-out (c) is directly above the pin (d). (2)
Needle/ Fabric/ Thread Chart NEEDLE, FABRIC, THREAD SELECTION GUIDE NEEDLE SIZE FABRICS Lightweight fabrics-thin cottons, voile, silk, muslin, 9-11 (70-80) interlocks, cotton knits, tricots, jerseys, crepes, woven polyester, shirt & blouse fabrics. 11-14 (80-90) 14 (90) 16 (100) 18 (110) Medium
Darning Plate For certain types of work, (e.g. darning or free-hand embroidery), the darning plate must be used. Install the darning plate as illustrated. For normal sewing, remove the darning plate. For free-motion sewing it is recommended to use a darning/embroidery foot, available as an optional
Inserting & Changing Needles Change the needle regularly, especially if it is showing signs of wear and causing problems. For best sewing results ® always use SINGER Brand Needles. D A Insert the needle as illustrated as follows: A. Loosen the needle clamp screw and tighten again after inserting
Changing the Bulb Disconnect the machine from the power supply by removing the plug from the main socket! Replace bulb with same type rated 10 watts (110-120V area) or 15 watts (220-240V area). — A B Loosen screw (A) as illustrated. (1) Remove the face plate (B). (2) Unscrew the bulb and install a
Troubleshooting Guide Problem Cause Correction Upper thread breaks 1. The machine is not threaded correctly. 2. The thread tension is too tight. 3. The thread is too thick for the needle. 4. The needle is not inserted correctly. 5. The thread is wound around the spool holder pin. 6. The needle is
Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to electrical/electronic products. If in doubt please contact your retailer for guidance.
Ïðè ïîäêëþ÷åíèè ýòîãî ïðîäóêòà íåîáõîäèìî âíèìàòåëüíî îçíàêîìèòüñÿ ñ ïðàâèëàìè ïî òåõíèêå áåçîïàñíîñòè, â ñîîòâåòñòâèè ñ äåéñòâóþùèì çàêîíîäàòåëüñòâîì â âàøåé ñòðàíå. Ïîæàëóéñòà, ó÷òèòå, ÷òî ïî îêîí÷àíèè ñðîêà ñëóæáû ýòîò ïðîäóêò äîëæåí áûòü óòèëèçèðîâàí â ñîîòâåòñòâèè ñ äåéñòâóþùèì Íàöèîíàëüíûì
Íåïîëàäêè è èõ óñòðàíåíèå Óäàëèòå âåðõíþþ íèòü è äîñòàíüòå øïóëüíîå ãíåçäî, ïîâåðíèòå âðó÷íóþ ìàõîâîå êîëåñî íà ñåáÿ è îò ñåáÿ è äîñòàíüòå îñòàòêè íèòîê è âîðñà. Çàïóòûâàíèå íèòè â ÷åëíîêå Òÿæåëûé õîä ìàøèíû 1. Çàìåíèòå èãëó 2. Ñìåíèòå ñìàçî÷íîå ìàñëî 1. Ïîâðåæäåíà èãëà 2. Ìàñëî ïëîõîãî êà÷åñòâà
Çàìåíà ëàìïî÷êè Îòêëþ÷èòå ìàøèíó îò ñåòè, âûíóâ ñåòåâîé øíóð èç ðîçåòêè! Èñïîëüçóéòå ëàìïî÷êè òàêîãî æå òèïà 15 âàòò (äëÿ 220240V). — A B Âûêðóòèòå âèíò (A) êàê ïîêàçàíî íà ðèñ. (1) Ñíèìèòå êðûøêó êîðïóñà (B). (2) Âûêðóòèòå ëàìïî÷êó è âñòàâüòå íîâóþ (C). (3) Ïîñòàâüòå êðûøêó êîðïóñà íà ìåñòî è
Óñòàíîâêà è ñìåíà èãëû Ìåíÿéòå èãëû ðåãóëÿðíî ïîñëå øèòüÿ êàæäîãî ïðîåêòà èëè ïðè âîçíèêíîâåíèè êàêèõ-ëèáî ïðîáëåì. ® Èñïîëüçóéòå èãëû SINGER äëÿ ëó÷øåãî êà÷åñòâà øèòüÿ. D A Âñòàâüòå èãëó, êàê ïîêàçàíî íà ðèñóíêå. A. Îñëàáüòå âèíò èãëû è çàòåì çàòÿíèòå åãî ñíîâà, ïîñëå òîãî, êàê âñòàâèòå íîâóþ
Øòîïàëüíàÿ ïëàñòèíà Äëÿ íåêîòîðûõ âèäîâ ðàáîò (íàïðèìåð, øòîïêà èëè øèòüå â òåõíèê å «ñâîáîäíîãî ïåðåäâèæåíèÿ») øòîïàëüíàÿ ïëàñòèíà äîëæíà áûòü óñòàíîâëåíà. Óñòàíîâèòå øòîïàëüíóþ ïëàñòèíó êàê óêàçàíî íà ðèñóíêå. Äëÿ øèòüÿ â îáû÷íîì ðåæèìå, ñíèìèòå øòîïàëüíóþ ïëàñòèíó. Äëÿ øèòüÿ â òåõíèêå
Ñîîòâåòñòâèå èãëû/ òêàíè/ íèòè Ðóêîâîäñòâî ïî âûáîðó èãë/ òêàíåé/ íèòîê Ïëîòíàÿ øåðñòü, òêàíü äëÿ ïàëüòî, îáèâî÷íûå òêàíè, íåêîòîðûå âèäû êîæè è âèíèë. 18 (110) Áîëüøèíñòâî ïðîäàâàåìûõ íèòåé ñòàíäàðòíîãî ðàçìåðà è ïðèìåíèìû äëÿ ýòèõ òêàíåé è ðàçìåðîâ èãë. Èñïîëüçóéòå ïîëèýñòðîâûå èëè ñèíòåòè÷åñêèå
Óñòàíîâêà äåðæàòåëÿ ëàïêè Ïîäíèìèòå äåðæàòåëü ëàïêè (à). Íàäåíüòå äåðæàòåëü ïðèæèìíîé ëàïêè (b), êàê ïîêàçàíî íà ðèñóíêå. (1) a a Óñòàíîâêà ïðèæèìíîé ëàïêè. Îïóñòèòå äåðæàòåëü ïðèæèìíîé ëàïêè (b), ïîêà âûåìêà (ñ) íå ñîâïàäåò ñ îñüþ (d). (2) Ïîäíèìèòå ðû÷àã (å). Îïóñòèòå äåðæàòåëü ïðèæèìíîé ëàïêè
Óñòàíîâêà ñúåìíîé ðàáî÷åé ïîâåðõíîñòè Äåðæèòå ñúåìíóþ ðàáî÷óþ ïîâåðõíîñòü ãîðèçîíòàëüíî è çàäâèíüòå åå ïî íàïðàâëåíèþ ñòðåëîê. (1) ×òîáû îòñîåäèíèòü ðàáî÷óþ ïîâåðõíîñòü, ïîòÿíèòå åå âëåâî. 1 Âíóòðåííÿÿ ÷àñòü ñúåìíîé ðàáî÷åé ïîâåðõíîñòè ìîæåò èñïîëüçîâàòüñÿ äëÿ õðàíåíèÿ àêñåññóàðîâ. 2 21
Øòîïêà â òåõíèêå ñâîáîäíîãî ïåðåäâèæåíèÿ, ñòåæêà * Ëàïêà äëÿ øòîïêè ÿâëÿåòñÿ äîïîëíèòåëüíûì àêñåñóàðîì, íå ïðèëàãàåòñÿ ê ìàøèíå. (1) Øòîïêà: Óñòàíîâèòå øòîïàëüíóþ ïëàñòèíó (2) è ñíèìèòå ëàïêîäåðæàòåëü (3). Ïðèñîåäèíèòå ëàïêó äëÿ øòîïêè ê ëàïêîäåðæàòåëþ. Ðû÷àã (à) äîëæåí íàõîäèòüñÿ çà âèíòîì
Ïðèøèâàíèå ïóãîâèöû (Òîëüêî äëÿ ìîäåëè 1409) Óñòàíîâèòå øòîïàëüíóþ ïëàñòèíó (1). Ñìåíèòå ïðèæèìíóþ ëàïêó íà ëàïêó äëÿ ïóãîâèöû (2). Ðàñïîëîæèòå èçäåëèå è ïóãîâèöó ïîä ïðèæèìíîé ëàïêîé, îïóñòèòå ëàïêó. Ñ ïîìîùüþ ðåãóëÿòîðà âûáîðà ñòðî÷åê óñòàíîâèòå » » è ñäåëàéòå íåñêîëüêî ôèêñèðóþùèõ ñòåæêîâ. Çàòåì
Ïðèøèâàíèå ïóãîâèöû (Òîëüêî äëÿ ìîäåëè 1408) Óñòàíîâèòå øòîïàëüíóþ ïëàñòèíó (1). Ñìåíèòå ïðèæèìíóþ ëàïêó íà ëàïêó äëÿ ïóãîâèöû (2). Ðàñïîëîæèòå èçäåëèå è ïóãîâèöó ïîä ïðèæèìíîé ëàïêîé, îïóñòèòå ëàïêó. Ñ ïîìîùüþ ðåãóëÿòîðà âûáîðà ñòðî÷åê óñòàíîâèòå âòîðîé âèä ñòðî÷êè çèã-çàã (êàê ïîêàçàíî íà
×åòûðåõ-øàãîâàÿ ïåòëÿ Ïîäãîòîâêà 1. Ñ í è ì è ò å Óí è â å ð ñ à ë ü í ó þ ï ð è æ è ì í ó þ ë à ï ê ó è ïðèñîåäèíèòå ëàïêó äëÿ Âûìåòûâàíèÿ ïåòåëü. 2. Îïðåäåëèòå äèàìåòð è òîëùèíó ïóãîâèöû, äîáàâüòå 0.3ñì íà çàêðåïêè, ñäåëàéòå ìåòêè äëÿ ðàçìåùåíèÿ ïåòëè íà èçäåëèè. (à) 3. Ðàçìåñòèòå òêàíü ïîä
Íåâèäèìàÿ ïîäãèáêà/ Áåëüåâàÿ ñòðî÷êà Äëÿ ïîòàéíîé ïîäðóáêè øòîð, áðþê, þáîê è ò.ä. Íåâèäèìàÿ ïîäãèáêà äëÿ ýëàñòè÷íûõ òêàíåé Íåâèäèìàÿ ïîäãèáêà äëÿ ïëîòíûõ òêàíûõ ìàòåðèàëîâ Âàæíî: Íåîáõîäèìà ïðàêòèêà äëÿ îñâîåíèÿ ýòîé îïåðàöèè. Âñåãäà äåëàéòå ïðîáíûé øîâ íà êóñî÷êå òêàíè. Òîëüêî äëÿ ìîäåëè 1409
Øèòüå íàçàä Äëÿ çàêðåïëåíèÿ øâà â íà÷àëå è êîíöå ñòðî÷êè, íàæèìàéòå íà ðû÷àã ðåâåðñà (À). Ñäåëàéòå íåñêîëüêî ñòåæêîâ â îáðàòíîì íàïðàâëåíèè. Îòïóñòèòå ðû÷àã è ìàøèíà ñíîâà áóäåò øèòü âïåðåä. (1) A Îêîí÷àíèå øèòüÿ Ïîâåðíèòå ìàõîâîå êîëåñî íà ñåáÿ (ïðîòèâ ÷àñîâîé ñòðåëêè) äëÿ òî ãî , ÷ òî áû ïðèâåñòè
Ïðÿìàÿ ñòðî÷êà Äëÿ íà÷àëà, óñòàíîâèòå Ðåãóëÿòîð âûáîðà ñòðî÷åê íà ïðÿìóþ ñòðî÷êó. (1) Ðàçìåñòèòå òêàíü ïîä ïðèæèìíîé ëàïêîé òàê, ÷òîáû êðàé òêàíè ñîâïàäàë ñ îäíîé èç âûáðàííûõ îòìåòîê íà èãîëüíîé ïëàñòèíå. (2) Îïóñòèòå ïðèæèìíóþ ëàïêó, íàæìèòå íà ïåäàëü óïðàâëåíèÿ, ÷òîáû íà÷àòü øèòü. (3) 1 2 3 14
Ðåãóëÿòîð äëèíû ñòåæêà (Òîëüêî äëÿ ìîäåëè 1409) Èñïîëüçîâàíèå Ðåãóëÿòîðà äëèíû ñòåæêà äëÿ ïðÿìîé ñòðî÷êè Ñ ïîìîùüþ Ðåãóëÿòîðà âûáîðà ñòðî÷åê âûáåðèòå ïðÿìóþ ñòðî÷êó (1). Ïîâåðíèòå Ðåãóëÿòîð äëèíû ñòåæêà â ñòîðîíó îòìåòêè «0», ïðè ýòîì äëèíà ñòåæêà óìåíüøèòñÿ. Äëèíà ñòåæêà áóäåò óâåëè÷èâàòüñÿ ïî
Âûáîð ñòðî÷êè ×òîáû óñòàíîâèòü âûáðàííóþ ñòðî÷êó âîñïîëüçóéòåñü ðåãóëÿòîðîì âûáîðà ñòðî÷åê (à). Ðåãóëÿòîð ìîæíî âðàùàòü â ëþáóþ ñòîðîíó. Íà ñëåäóþùåé ñòðàíèöå ñîäåðæèòñÿ èíôîðìàöèÿ î ðåêîìåíäóåìîé äëèíå ñòåæêà äëÿ ðàçíûõ âèäîâ ñòðî÷åê. a b Óñòàíîâèòå äëèíó ñòåæêà ñ ïîìîùüþ ðåãóëÿòîðà äëèíû
Íàòÿæåíèå íèòè Íàòÿæåíèå âåðõíåé íèòè Ñòàíäàðòíîå íàòÿæåíèå íèòè íàõîäèòñÿ â ïîëîæåíèè: «4». (1) Äëÿ óâåëè÷åíèÿ íàòÿæåíèÿ íèòè ïîâåðíèòå ðåãóëÿòîð íà áîëüøåå çíà÷åíèå. À. Íîðìàëüíîå íàòÿæåíèå íèòè äëÿ ïðÿìîé ñòðî÷êè. Â. Íåäîñòàòî÷íîå íàòÿæåíèå íèòè äëÿ ïðÿìîé ñòðî÷êè. Ïåðåâåäèòå ðåãóëÿòîð íà
Ïîäúåì íèæíåé íèòè Ïðèäåðæèâàéòå âåðõíþþ íèòü ëåâîé ðóêîé. Ïîâåðíèòå ìàõîâîå êîëåñî (1) íà ñåáÿ (ïðîòèâ ÷àñîâîé ñòðåëêè), îïóñòèòå è çàòåì ïîäíèìèòå èãëó. Âàæíî: Åñëè âäðóã ñëîæíî ïîäíÿòü íèæíþþ íèòü, óáåäèòåñü, ÷òî îíà íå çàñòðÿëà â ñúåìíîé ðàáî÷åé ïîâåðõíîñòè. 1 Ìÿãêî ïîòÿíèòå çà âåðõíþþ íèòü è
Çàïðàâêà âåðõíåé íèòè Ýòî ïðîñòàÿ îïåðàöèÿ, íî î÷åíü âàæíî âûïîëíÿòü åå ïðàâèëüíî, âî èçáåæàíèå ïðîÿâëåíèÿ ïðîáëåì ïðè øèòüå. — Ïîäíèìèòå èãëó â íàèâûñøåå ïîëîæåíèå (1) è ïðîäîëæàéòå ïîâîðà÷èâàòü ìàõîâîå êîëåñî íà ñåáÿ, ïðîòèâ ÷àñîâîé ñòðåëêè, ïîêà èãëà ñëåãêà íå îïóñòèòñÿ, ÷òîáû îñâîáîäèòü äèñê
Óñòàíîâêà øïóëüíîãî êîëïà÷êà Âî âðåìÿ óñòàíîâêè èëè ñíÿòèÿ øïóëüíîãî êîëïà÷êà èãëà äîëæíà âñåãäà íàõîäèòüñÿ â ñàìîì âåðõíåì ïîëîæåíèè. 1. Îòêðîéòå ÷åëíî÷íûé îòñåê. 2. Îòîãíèòå çàùåëêó øïóëüíîãî êîëïà÷êà è âûíüòå øïóëüíûé êîëïà÷îê. 3. Âîçüìèòå øïóëüíûé êîëïà÷îê îäíîé ðóêîé. Âñòàâüòå øïóëüêó òàêèì
Íàìîòêà øïóëüêè — Íàäåíüòå êàòóøêó è ôåòðîâûé äèñê (à) íà ãîðèçîíòàëüíûé äåðæàòåëü. (1) — Îáâåäèòå íèòü âîêðóã äèñêà, ðåãóëèðóþùåãî íàòÿæåíèå íèòè, ïî ÷àñîâîé ñòðåëêå. (2) — Íàìîòàéòå íèòü íà øïóëüêó (êàê óêàçàíî íà ðèñóíêå) è íàäåíüòå íà ñòåðæåíü äëÿ íàìîòêè øïóëüêè. (3) — Îòâåäèòå âïðàâî ðû÷àã
Àêñåññóàðû Ñòàíäàðòíûå àêñåññóàðû (1) a. Óíèâåðñàëüíàÿ ïðèæèìíàÿ ëàïêà b. Ïðèæèìíàÿ ëàïêà äëÿ âøèâàíèÿ ìîëíèè c. Ïðèæèìíàÿ ëàïêà äëÿ âûìåòûâàíèÿ ïåòåëü d. Ïðèæèìíàÿ ëàïêà äëÿ ïðèøèâàíèÿ ïóãîâèöû e. L-îòâåðòêà f. Ïðîðåçàòåëü ïåòåëü/ Êèñòî÷êà g. Ôåòðîâàÿ ïðîêëàäêà (2x) h. Óïàêîâêà èãë (3x) i.
Äâóõøàãîâûé ïîäúåì ëàïêè Ïðè øèòüå ìíîãîñëîéíûõ èëè òîëñòûõ òêàíåé ïðèæèìíàÿ ëàïêà äîëæíà áûòü ïîäíÿòà â ñàìîå âåðõíåå ïîëîæåíèå äëÿ îáëåã÷åíèÿ ïðîòàñêèâàíèÿ èçäåëèé ïîä ëàïêó (À). A 5
Ïîäêëþ÷åíèå ìàøèíû ê ýëåêòðîñåòè Ïîäêëþ÷èòå ìàøèíó ê ýëåêòðîñåòè, êàê ïîêàçàíî íà ðèñóíêå. (1) Âñòàâüòå âèëêó â ðîçåòêó. (2) A Âíèìàíèå: Îòêëþ÷àéòå ìàøèíó îò ñåòè, åñëè íå èñïîëüçóåòå åå äëèòåëüíîå âðåìÿ. Ïåäàëü óïðàâëåíèÿ Ïðè ïîìîùè íîæíîé ïåäàëè âû ðåãóëèðóåòå ñêîðîñòü ìàøèíû. (3) Âíèìàíèå:
Îñíîâíûå äåòàëè ìàøèíû 12. Ðó÷êà 13. Ðû÷àã íàìîòêè øïóëüêè 14. Äåðæàòåëè êàòóøåê 15. Ìàõîâîå êîëåñî 16. Âûêëþ÷àòåëü ìàøèíû è ëàìïî÷êè 17. Ãëàâíûé ðàçúåì äëÿ øíóðà 18. Íèòåâîäèòåëü äëÿ øïóëüêè 19. Ðû÷àã ïîäúåìà ëàïêè 20. Êîíòðîëü ñêîðîñòè 21. Âèëêà ñåòåâîãî øíóðà 3
Îñíîâíûå äåòàëè ìàøèíû 1. Íàòÿæåíèå íèòè 2. Ðû÷àã — íèòåïðèòÿãèâàòåëü 3. Íîæ äëÿ îáðåçêè íèòè 4. Êîðïóñ ìàøèíû 5. Ïðèæèìíàÿ ëàïêà 6. Èãîëüíàÿ ïëàñòèíà 7. Ñúåìíàÿ ðàáî÷àÿ ïîâåðõíîñòü/ ñâîáîäíûé ðóêàâ 8. Ðåãóëÿòîð âûáîðà ñòðî÷åê 9. Ñòîïîð íàìîòêè øïóëüêè 10. Ðåãóëÿòîð äëèíû ñòåæêà (Òîëüêî äëÿ ìîäåëè
Îãëàâëåíèå ÇÍÀÊÎÌÑÒÂÎ Ñ ÌÀØÈÍÎÉ Îñíîâíûå äåòàëè ìàøèíû ……………………………………………………………………………………………………………………………….2/3 Ïîäêëþ÷åíèå ìàøèíû ê ýëåêòðîñåòè
Ïîçäðàâëÿåì Âû ñòàëè îáëàäàòåëåì íîâîé øâåéíîé ìàøèíû è òåïåðü ìîæåòå íà÷àòü îòêðûâàòü íîâûå ïóòè â òâîð÷åñòâå. Ñ ýòîãî ìîìåíòà âû óçíàåòå íàñêîëüêî ëåãêî è óäîáíî ìîæíî øèòü íà ñîâðåìåííîé øâåéíîé ìàøèíå. Ïîæàëóéñòà, âíèìàòåëüíî ïðî÷èòàéòå èíñòðóêöèþ ïî ýêñïëóàòàöèè ìàøèíû — ýòî ñàìûé ëåãêèé ïóòü
Ïðàâèëà òåõíèêè áåçîïàñíîñòè Ïðåæäå ÷åì âêëþ÷èòü øâåéíóþ ìàøèíó, âíèìàòåëüíî ïðî÷èòàéòå ñëåäóþùèå ðåêîìåíäàöèè: ÎÏÀÑÍÎ — âî èçáåæàíèå ýëåêòðè÷åñêîãî øîêà: 1. Íåëüçÿ îñòàâëÿòü âêëþ÷åííóþ ìàøèíó áåç ïðèñìîòðà. 2. Íåîáõîäèìî îòêëþ÷àòü ìàøèíó îò ýëåêòðîñåòè, åñëè ñîáèðàåòåñü åå ÷èñòèòü. 3. Âñåãäà
1408 / 1409 Èíñòðóêöèÿ ïî ýêñïëóàòàöèè 021M1A0103( ) Apr/10 SINGER 1408/1409(M10A/M20A)