Ericsson rx8330 инструкция на русском

  • Страница 1

    RX8310/15/30 Distribution Receivers Software Version 4.3.2 USER GUIDE EN/LZT 790 0008/1 R1A[…]

  • Страница 2

    RX8310/15/30 Distribution Receivers Copyright © Copyright Ericsson AB 2011. All rights reserved. Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due t o continued progress in methodology, design and manufact[…]

  • Страница 3

    Contents Contents 1 Introduction ……………………………………………………………………………….. 5 1.1 Who Should Use this User Guide? …………………………………………………. 5 1.2 What Equipment is Covered by this User Guide? …………………………….. 5 1.3 Hardware and Software Options …[…]

  • Страница 4

    Contents EN/LZT 790 0008/1 R1A 2011-03 -30 4 (40) List of Figures Figure 1 Rear Panel Connectors (RX8310/BAS with RX83XX/HWO/IP/OUT) …… 9 Figure 2 Rear Panel Connectors (RX8315/BAS with RX83XX/HWO/IP/OUT) …… 9 Figure 3 Rear Panel Connectors (RX8330/BAS with RX83XX/HWO/IP/OUT) …. 10 Figure 4 Front Panel LEDs and Pushbuttons ……………[…]

  • Страница 5

    Introduction 1 Introduction 1.1 Who Should Use this User Guide? This User Guide is written for operators/users of the RX8310, RX8315 and RX8330 Distribution Receivers to assist in installation and operation. Detailed information can be found in the Reference Guide companion document which is issued on CD. Warning! Do not remove the covers of this e[…]

  • Страница 6

    Introduction 1.3 Hardware and Software Options See Table 2, 3, 4 and 5 for a list of hardware and software options available with the receivers. Detailed information is in the Reference Guide . T able 2 RX8310/RX8315/RX8330 Hardware Options Marketing Code Price Object Number Supply Object Number Description RX83XX/HWO/IP/OUT FAZ 101 0108/22 ROA 128[…]

  • Страница 7

    Introduction T able 4 RX8330 Hardware Options Marketing Code Price Objec t Number Supply Object Number Description RX83XX/HWO/RSECAM FAZ 101 0108/33 ROA 128 4418 Russi an SECAM Output Card T able 5 RX8330 Software Options Marketing Code Price Object Number Supply Object Number Description RX83XX/SWO/BISS FAZ 101 0108/30 FAT 102 0132 BISS Modes 1 an[…]

  • Страница 8

    Installing the Equipment 2 Inst alling the Equipment 2.1 Introduction For best performance and reliability follow the instructions for site requirements and installation in the Reference Guide and only use installation accessories recommended by the manufacturers. Warning! Do not remove the covers of this equipment. Hazardous voltages are present w[…]

  • Страница 9

    Installing the Equipment Warning! The Technical Earth is not a Protective earth for electric shock protection. This unit must be correctly earthed through the molded plug supplied. If the local mains supply does not have an earth conductor do not connect the unit. Contact Customer Services for advice. Before connecting the unit to the supply, check[…]

  • Страница 10

    Installing the Equipment ETHE RNET 1- 2 TECHNICA L E A RT H ASI/ S DI O UT 1- 2 CVBS A LA RM AS I I N P U T AC P O W E R RF IN 1-4 AU D IO O UT (1 ) 1- 2 IP OU T 1 -2 CA INTERF ACE Figure 3 Rear Panel Connectors (RX8330/BAS with RX83XX/HWO/IP/OUT) Table 6 Types of Connector Type of Connector Description RF IN 1,2,3 & 4 F-type connectors for DVB[…]

  • Страница 11

    Installing the Equipment 2.5 Connecting the Receiver to the Power Supply Warning! Do not overload wall outlets and extension cords as this can r esult in a risk of fire or electric shock. As no mains switch is fitted to this unit, ensure the local powe r supply is switched OFF before connecting the supply cord. The receiver is not fitted with an on[…]

  • Страница 12

    Quick Start Guide: Connect- P ower — Configure 3 Quick S tart Guide: Connect-Power-Configure 3.1 Connecting the Receiver The following points should be noted when making signal connections to the receiver: • If you have an incoming satellite RF feed, this should be connected to the rear panel connector marked RF IN 1 — 4 . • If you have an inco[…]

  • Страница 13

    Quick Start Guide: Connect- P ower — Configure 2. Switch on the AC power supply to the unit at the wall or rack outlet. Note: The RX8310/15/30 Receivers do NOT contain a power on/off switch. 3. After a short period of initialization the following screen is displayed on the Front Panel: INITIALIZING 4.3.2 (Bank 0) 4. During initialization, confirm t[…]

  • Страница 14

    Quick Start Guide: Connect- P ower — Configure 8. Set the set the LNB power output level A description of each of these User Settings can be found in the Reference Guide . Note: If the unit has successful ly locked to the incoming feed, then the TS Lock value in menu Input should be LOCKED . 3.4 Selecting a Decode Service (Program) To select a deco[…]

  • Страница 15

    Quick Start Guide: Connect- P ower — Configure • Alternative audio components may be selected from the service tab on the Web Control interface 3.7 Configuring for Single-serv ice Decryption When configuring for Single-service Decryption the following points shou ld be observed: • If the service selected for video decode contains encrypted comp[…]

  • Страница 16

    Front P a nel C ontrol 4 Front Panel Control 4.1 Introduction The front panel display and keypad can be used to configure, control and monitor the receiver when an external control system is not used. Note: A list of receiver User Settings that may be viewed or changed via the front panel and those that may be viewed or changed via the external web[…]

  • Страница 17

    Front P a nel C ontrol 4.3.2 LCD A 2-line x 40-character back-lit dot-matrix Liquid Crystal Display (LCD) displays various menus and settings. The menus and setting available will vary depending on which options have been enabled through the purchase of a suitable lice nse. 4.3.3 Arrow Pushbuttons Four arrow pushbuttons (or keys) are used to naviga[…]

  • Страница 18

    Front P a nel C ontrol 4.4 Front Panel Menus An overview of the available Front Panel menus is shown below. The menus and settings available will vary depending on which receiver model is being used and which options have been enabled through the purchase of a suitable lice nse. Note: The menu structure is subject to change as further functionality[…]

  • Страница 19

    Front P a nel C ontrol 4.4.1 Menu Structure The Front Panel menus and sub-menus, av ailable on the LCD, provide the configuration parameters that may be viewed, selected and/or modified. • System — Provides sub-menus for viewing/config uring the receiver hardware and access parameters. — Network – Enables the input and display of the addresses […]

  • Страница 20

    Front P a nel C ontrol — TS Feed Selection — Enables selection of the descrambling for the Transport Stream Feed. • Presets — Provides sub-menus for viewing, storing and retrieving up to 40 sets of input configuration parameters (tuning parameters and service selectio ns). — Preset State — Enables the current list of presets to be viewed. — Selec[…]

  • Страница 21

    Web Br o w ser Control 5 W eb Browser Control 5.1 Introduction A personal computer (PC) running a Web Browser can be used to configure, control and monitor the receiver remotely. The following web browsers have been tested: • Microsoft Internet Explorer (This is the only browser supported by Ericsso n) • Mozilla Firefox (Functional but unsuppor[…]

  • Страница 22

    Web Br o w ser Control Unit Model Number and Name About button Header Function Tabs Navi g ation Path Toolbar Main Web Page Results Frame Figure 6 Web Page Overview (T ypical) • Header – The header of the web page displays the Ericsson logo and the unit model number name. At the right-hand side of the header an About button which, when clicked,[…]

  • Страница 23

    Web Br o w ser Control web page. When you switch between tabs, the browser remembers the path for each tab. • Navigation Path – The web pages are organized into a tree-like structur e, like the directory on a computer. The current complete navigation path is always displayed at the top of the web page, which shows the route taken to the current[…]

  • Страница 24

    Web Br o w ser Control 5.3 W eb Pages 5.3.1 Status This web page shows a number of top-level parameters indicating the current status of the receiver. Figure 8 S t atus Web Page 5.3.2 Device Info The Device Info web page provides access to system-level settings for the receiver and can be used to enable the Front Panel Lockout Facility and initiate[…]

  • Страница 25

    Web Br o w ser Control Figure 9 Device Info Web Page This page also provides buttons to the following further web pages: • Build – provides details of equipment build and version numbers. No user- editable fields. • Environment – provides details of the phy sical environment of the equipment such as temperature and fan speed. No user-editab[…]

  • Страница 26

    Web Br o w ser Control 5.3.3 Alarms The Alarms web page provides access to the alarms settings for the receiver. The contents of this page are composed mainly of fields with drop-down menus which allow the setting or masking of various alarms and check boxes which can be used to activate relay mapping. Two of the al arm fields, namely C/N (Carrier-[…]

  • Страница 27

    Web Br o w ser Control Figure 10 Alarms W eb Page 5.3.4 Customization Web Page The Customization web page provides acce ss to the list of licenses enabled on the equipment and to enable further licenses (as purchased) by entering the custom key provided. Figure 1 1 Customization W eb Page 5.3.5 CA The CA web page allows viewing and modification of […]

  • Страница 28

    Web Br o w ser Control Figure 12 CA W eb Page 5.3.6 Input The Input Web Page provides access to the parameters of the various inputs to the receiver. The page, which is displayed, depends on which Input card is fitted. The options are: • Satellite Input Card The Input page displays parameters for input feed lock status and bit rate, primary and s[…]

  • Страница 29

    Web Br o w ser Control Figure 13 Input Web Page Click on the Satellite Input button on the Input page to display a further sub page. Figure 14 Input > SA T Input Sub Page The only field which may be edited by the user is the RF Selection field which allows selection of the appropriate RF Input. There are also four Configuration buttons which all[…]

  • Страница 30

    Web Br o w ser Control 5.3.7 Service Plus The Service Plus web page provides access to the various encryption and encoding services available to the receiver. A Se rvice Control table is displayed showing which services are available. The only use r-editable fields in this table are the Decrypt and Decode checkboxes. The user can select Decry pt , […]

  • Страница 31

    Web Br o w ser Control Figure 16 Decode Web Page 5.3.9 Output The Output web page provides access to the output feed parameters of the receiver. EN/LZT 790 0008/1 R1A 2011-03 -30 31 (40)[…]

  • Страница 32

    Web Br o w ser Control Figure 17 Output Web Page 5.3.10 Download The Download web page provides access to the over air download status of the receiver. There are no user-editable fields on this page. EN/LZT 790 0008/1 R1A 2011-03 -30 32 (40)[…]

  • Страница 33

    Web Br o w ser Control Figure 18 Download Web Page 5.3.11 SNMP This page gives access to the Simple Network Management Protocol (SNMP) parameters for the receiver, including protocol selection and MIB parameters. Figure 19 SNMP W eb Page 5.3.12 Presets The Presets web page gives access to a list of 40 preset configurations. This feature may be used[…]

  • Страница 34

    Web Br o w ser Control Figure 20 Presets W eb Page 5.3.13 Save/Load The Save/Load web page provides a range of configuration download and upload facilities, including saving and restoring unit confi guration, saving unit MIB files, saving alarm log files and saving splice log files. EN/LZT 790 0008/1 R1A 2011-03 -30 34 (40)[…]

  • Страница 35

    Web Br o w ser Control Figure 21 Save/Load Web Page 5.3.14 Help The Help web page gives access to a Web Interface User Guide which provides a brief description of the interface functionality. Figure 22 Help Web Page EN/LZT 790 0008/1 R1A 2011-03 -30 35 (40)[…]

  • Страница 36

    Equipment P a ckaging 6 Equipment Packaging 6.1 Packaging S t atement The outer carton and any cardboard inserts are made from 82% recycled material and are fully recyclable. The Stratocell ® or Ethafoam 220 ® polyethylene foam inserts can be easily recycled with other low density polyethylene (LDPE) materials 6.2 Packaging Markings The symbols p[…]

  • Страница 37

    Materials Declarations 7 Materials Declarations 7.1 Overview Ericsson products are designed and manufactured in keeping with good environmental practice. Our component and materials selection policy prohibits the use of a range of potentially hazardous materials. In addition, we comply with relevant environmental legislation. 7.2 For the European U[…]

  • Страница 38

    Disposal of this Equipment 8 Disposal of this Equipment 8.1 General Dispose of this equipment safely at the end of its life. Local codes and/or environmental restrictions may affect its disposal. Regulations, policies an d/or environmental restrictions differ throughout the world. Contact your local jurisdiction or local authority for specific advi[…]

  • Страница 39

    Re c y cling 9 Recycling Ericsson SA TV Recycling has a process facility that enables customers t o return Old and End-of-Life Products for recycling if it is required. Ericsson provides assistance to customers and recyclers thr ough our Ericsson and SATV Recycling eBusiness Portal. This can be reached at: https://ebusiness.ericsson .net/ . To gain[…]

  • Страница 40

    Re c y cling EN/LZT 790 0008/1 R1A 2011-03 -30 40 (40)[…]

Скачать

Страница из 40

RX8310/15/30 Distribution Receivers

Software Version 4.3.2

USER GUIDE

EN/LZT 790 0008/1 R1A  

  • Page 1: Ericsson RX8330

    RX8310/15/30 Distribution Receivers Software Version 4.3.2 USER GUIDE EN/LZT 790 0008/1 R1A[…]

  • Page 2: Ericsson RX8330

    RX8310/15/30 Distribution Receivers Copyright © Copyright Ericsson AB 2011. All rights reserved. Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due t o continued progress in methodology, design and manufact[…]

  • Page 3: Ericsson RX8330

    Contents Contents 1 Introduction ……………………………………………………………………………….. 5 1.1 Who Should Use this User Guide? …………………………………………………. 5 1.2 What Equipment is Covered by this User Guide? …………………………….. 5 1.3 Hardware and Software Options …[…]

  • Page 4: Ericsson RX8330

    Contents EN/LZT 790 0008/1 R1A 2011-03 -30 4 (40) List of Figures Figure 1 Rear Panel Connectors (RX8310/BAS with RX83XX/HWO/IP/OUT) …… 9 Figure 2 Rear Panel Connectors (RX8315/BAS with RX83XX/HWO/IP/OUT) …… 9 Figure 3 Rear Panel Connectors (RX8330/BAS with RX83XX/HWO/IP/OUT) …. 10 Figure 4 Front Panel LEDs and Pushbuttons ……………[…]

  • Page 5: Ericsson RX8330

    Introduction 1 Introduction 1.1 Who Should Use this User Guide? This User Guide is written for operators/users of the RX8310, RX8315 and RX8330 Distribution Receivers to assist in installation and operation. Detailed information can be found in the Reference Guide companion document which is issued on CD. Warning! Do not remove the covers of this e[…]

  • Page 6: Ericsson RX8330

    Introduction 1.3 Hardware and Software Options See Table 2, 3, 4 and 5 for a list of hardware and software options available with the receivers. Detailed information is in the Reference Guide . T able 2 RX8310/RX8315/RX8330 Hardware Options Marketing Code Price Object Number Supply Object Number Description RX83XX/HWO/IP/OUT FAZ 101 0108/22 ROA 128[…]

  • Page 7: Ericsson RX8330

    Introduction T able 4 RX8330 Hardware Options Marketing Code Price Objec t Number Supply Object Number Description RX83XX/HWO/RSECAM FAZ 101 0108/33 ROA 128 4418 Russi an SECAM Output Card T able 5 RX8330 Software Options Marketing Code Price Object Number Supply Object Number Description RX83XX/SWO/BISS FAZ 101 0108/30 FAT 102 0132 BISS Modes 1 an[…]

  • Page 8: Ericsson RX8330

    Installing the Equipment 2 Inst alling the Equipment 2.1 Introduction For best performance and reliability follow the instructions for site requirements and installation in the Reference Guide and only use installation accessories recommended by the manufacturers. Warning! Do not remove the covers of this equipment. Hazardous voltages are present w[…]

  • Page 9: Ericsson RX8330

    Installing the Equipment Warning! The Technical Earth is not a Protective earth for electric shock protection. This unit must be correctly earthed through the molded plug supplied. If the local mains supply does not have an earth conductor do not connect the unit. Contact Customer Services for advice. Before connecting the unit to the supply, check[…]

  • Page 10: Ericsson RX8330

    Installing the Equipment ETHE RNET 1- 2 TECHNICA L E A RT H ASI/ S DI O UT 1- 2 CVBS A LA RM AS I I N P U T AC P O W E R RF IN 1-4 AU D IO O UT (1 ) 1- 2 IP OU T 1 -2 CA INTERF ACE Figure 3 Rear Panel Connectors (RX8330/BAS with RX83XX/HWO/IP/OUT) Table 6 Types of Connector Type of Connector Description RF IN 1,2,3 & 4 F-type connectors for DVB[…]

  • Page 11: Ericsson RX8330

    Installing the Equipment 2.5 Connecting the Receiver to the Power Supply Warning! Do not overload wall outlets and extension cords as this can r esult in a risk of fire or electric shock. As no mains switch is fitted to this unit, ensure the local powe r supply is switched OFF before connecting the supply cord. The receiver is not fitted with an on[…]

  • Page 12: Ericsson RX8330

    Quick Start Guide: Connect- P ower — Configure 3 Quick S tart Guide: Connect-Power-Configure 3.1 Connecting the Receiver The following points should be noted when making signal connections to the receiver: • If you have an incoming satellite RF feed, this should be connected to the rear panel connector marked RF IN 1 — 4 . • If you have an inco[…]

  • Page 13: Ericsson RX8330

    Quick Start Guide: Connect- P ower — Configure 2. Switch on the AC power supply to the unit at the wall or rack outlet. Note: The RX8310/15/30 Receivers do NOT contain a power on/off switch. 3. After a short period of initialization the following screen is displayed on the Front Panel: INITIALIZING 4.3.2 (Bank 0) 4. During initialization, confirm t[…]

  • Page 14: Ericsson RX8330

    Quick Start Guide: Connect- P ower — Configure 8. Set the set the LNB power output level A description of each of these User Settings can be found in the Reference Guide . Note: If the unit has successful ly locked to the incoming feed, then the TS Lock value in menu Input should be LOCKED . 3.4 Selecting a Decode Service (Program) To select a deco[…]

  • Page 15: Ericsson RX8330

    Quick Start Guide: Connect- P ower — Configure • Alternative audio components may be selected from the service tab on the Web Control interface 3.7 Configuring for Single-serv ice Decryption When configuring for Single-service Decryption the following points shou ld be observed: • If the service selected for video decode contains encrypted comp[…]

  • Page 16: Ericsson RX8330

    Front P a nel C ontrol 4 Front Panel Control 4.1 Introduction The front panel display and keypad can be used to configure, control and monitor the receiver when an external control system is not used. Note: A list of receiver User Settings that may be viewed or changed via the front panel and those that may be viewed or changed via the external web[…]

  • Page 17: Ericsson RX8330

    Front P a nel C ontrol 4.3.2 LCD A 2-line x 40-character back-lit dot-matrix Liquid Crystal Display (LCD) displays various menus and settings. The menus and setting available will vary depending on which options have been enabled through the purchase of a suitable lice nse. 4.3.3 Arrow Pushbuttons Four arrow pushbuttons (or keys) are used to naviga[…]

  • Page 18: Ericsson RX8330

    Front P a nel C ontrol 4.4 Front Panel Menus An overview of the available Front Panel menus is shown below. The menus and settings available will vary depending on which receiver model is being used and which options have been enabled through the purchase of a suitable lice nse. Note: The menu structure is subject to change as further functionality[…]

  • Page 19: Ericsson RX8330

    Front P a nel C ontrol 4.4.1 Menu Structure The Front Panel menus and sub-menus, av ailable on the LCD, provide the configuration parameters that may be viewed, selected and/or modified. • System — Provides sub-menus for viewing/config uring the receiver hardware and access parameters. — Network – Enables the input and display of the addresses […]

  • Page 20: Ericsson RX8330

    Front P a nel C ontrol — TS Feed Selection — Enables selection of the descrambling for the Transport Stream Feed. • Presets — Provides sub-menus for viewing, storing and retrieving up to 40 sets of input configuration parameters (tuning parameters and service selectio ns). — Preset State — Enables the current list of presets to be viewed. — Selec[…]

  • Page 21: Ericsson RX8330

    Web Br o w ser Control 5 W eb Browser Control 5.1 Introduction A personal computer (PC) running a Web Browser can be used to configure, control and monitor the receiver remotely. The following web browsers have been tested: • Microsoft Internet Explorer (This is the only browser supported by Ericsso n) • Mozilla Firefox (Functional but unsuppor[…]

  • Page 22: Ericsson RX8330

    Web Br o w ser Control Unit Model Number and Name About button Header Function Tabs Navi g ation Path Toolbar Main Web Page Results Frame Figure 6 Web Page Overview (T ypical) • Header – The header of the web page displays the Ericsson logo and the unit model number name. At the right-hand side of the header an About button which, when clicked,[…]

  • Page 23: Ericsson RX8330

    Web Br o w ser Control web page. When you switch between tabs, the browser remembers the path for each tab. • Navigation Path – The web pages are organized into a tree-like structur e, like the directory on a computer. The current complete navigation path is always displayed at the top of the web page, which shows the route taken to the current[…]

  • Page 24: Ericsson RX8330

    Web Br o w ser Control 5.3 W eb Pages 5.3.1 Status This web page shows a number of top-level parameters indicating the current status of the receiver. Figure 8 S t atus Web Page 5.3.2 Device Info The Device Info web page provides access to system-level settings for the receiver and can be used to enable the Front Panel Lockout Facility and initiate[…]

  • Page 25: Ericsson RX8330

    Web Br o w ser Control Figure 9 Device Info Web Page This page also provides buttons to the following further web pages: • Build – provides details of equipment build and version numbers. No user- editable fields. • Environment – provides details of the phy sical environment of the equipment such as temperature and fan speed. No user-editab[…]

  • Page 26: Ericsson RX8330

    Web Br o w ser Control 5.3.3 Alarms The Alarms web page provides access to the alarms settings for the receiver. The contents of this page are composed mainly of fields with drop-down menus which allow the setting or masking of various alarms and check boxes which can be used to activate relay mapping. Two of the al arm fields, namely C/N (Carrier-[…]

  • Page 27: Ericsson RX8330

    Web Br o w ser Control Figure 10 Alarms W eb Page 5.3.4 Customization Web Page The Customization web page provides acce ss to the list of licenses enabled on the equipment and to enable further licenses (as purchased) by entering the custom key provided. Figure 1 1 Customization W eb Page 5.3.5 CA The CA web page allows viewing and modification of […]

  • Page 28: Ericsson RX8330

    Web Br o w ser Control Figure 12 CA W eb Page 5.3.6 Input The Input Web Page provides access to the parameters of the various inputs to the receiver. The page, which is displayed, depends on which Input card is fitted. The options are: • Satellite Input Card The Input page displays parameters for input feed lock status and bit rate, primary and s[…]

  • Page 29: Ericsson RX8330

    Web Br o w ser Control Figure 13 Input Web Page Click on the Satellite Input button on the Input page to display a further sub page. Figure 14 Input > SA T Input Sub Page The only field which may be edited by the user is the RF Selection field which allows selection of the appropriate RF Input. There are also four Configuration buttons which all[…]

  • Page 30: Ericsson RX8330

    Web Br o w ser Control 5.3.7 Service Plus The Service Plus web page provides access to the various encryption and encoding services available to the receiver. A Se rvice Control table is displayed showing which services are available. The only use r-editable fields in this table are the Decrypt and Decode checkboxes. The user can select Decry pt , […]

  • Page 31: Ericsson RX8330

    Web Br o w ser Control Figure 16 Decode Web Page 5.3.9 Output The Output web page provides access to the output feed parameters of the receiver. EN/LZT 790 0008/1 R1A 2011-03 -30 31 (40)[…]

  • Page 32: Ericsson RX8330

    Web Br o w ser Control Figure 17 Output Web Page 5.3.10 Download The Download web page provides access to the over air download status of the receiver. There are no user-editable fields on this page. EN/LZT 790 0008/1 R1A 2011-03 -30 32 (40)[…]

  • Page 33: Ericsson RX8330

    Web Br o w ser Control Figure 18 Download Web Page 5.3.11 SNMP This page gives access to the Simple Network Management Protocol (SNMP) parameters for the receiver, including protocol selection and MIB parameters. Figure 19 SNMP W eb Page 5.3.12 Presets The Presets web page gives access to a list of 40 preset configurations. This feature may be used[…]

  • Page 34: Ericsson RX8330

    Web Br o w ser Control Figure 20 Presets W eb Page 5.3.13 Save/Load The Save/Load web page provides a range of configuration download and upload facilities, including saving and restoring unit confi guration, saving unit MIB files, saving alarm log files and saving splice log files. EN/LZT 790 0008/1 R1A 2011-03 -30 34 (40)[…]

  • Page 35: Ericsson RX8330

    Web Br o w ser Control Figure 21 Save/Load Web Page 5.3.14 Help The Help web page gives access to a Web Interface User Guide which provides a brief description of the interface functionality. Figure 22 Help Web Page EN/LZT 790 0008/1 R1A 2011-03 -30 35 (40)[…]

  • Page 36: Ericsson RX8330

    Equipment P a ckaging 6 Equipment Packaging 6.1 Packaging S t atement The outer carton and any cardboard inserts are made from 82% recycled material and are fully recyclable. The Stratocell ® or Ethafoam 220 ® polyethylene foam inserts can be easily recycled with other low density polyethylene (LDPE) materials 6.2 Packaging Markings The symbols p[…]

  • Page 37: Ericsson RX8330

    Materials Declarations 7 Materials Declarations 7.1 Overview Ericsson products are designed and manufactured in keeping with good environmental practice. Our component and materials selection policy prohibits the use of a range of potentially hazardous materials. In addition, we comply with relevant environmental legislation. 7.2 For the European U[…]

  • Page 38: Ericsson RX8330

    Disposal of this Equipment 8 Disposal of this Equipment 8.1 General Dispose of this equipment safely at the end of its life. Local codes and/or environmental restrictions may affect its disposal. Regulations, policies an d/or environmental restrictions differ throughout the world. Contact your local jurisdiction or local authority for specific advi[…]

  • Page 39: Ericsson RX8330

    Re c y cling 9 Recycling Ericsson SA TV Recycling has a process facility that enables customers t o return Old and End-of-Life Products for recycling if it is required. Ericsson provides assistance to customers and recyclers thr ough our Ericsson and SATV Recycling eBusiness Portal. This can be reached at: https://ebusiness.ericsson .net/ . To gain[…]

  • Page 40: Ericsson RX8330

    Re c y cling EN/LZT 790 0008/1 R1A 2011-03 -30 40 (40)[…]

  • Ericsson RX8330 — page 1

    RX8310/15/30 Distribution Receivers Software Version 4.3.2 USER GUIDE EN/LZT 790 0008/1 R1A …

  • Ericsson RX8330 — page 2

    RX8310/15/30 Distribution Receivers Copyright © Copyright Ericsson AB 2011. All rights reserved. Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due t o continued progress in methodology, design and manufact …

  • Ericsson RX8330 — page 3

    Contents Contents 1 Introduction ……………………………………………………………………………….. 5 1.1 Who Should Use this User Guide? …………………………………………………. 5 1.2 What Equipment is Covered by this User Guide? …………………………….. 5 1.3 Hardware and Software Options … …

  • Ericsson RX8330 — page 4

    Contents EN/LZT 790 0008/1 R1A 2011-03 -30 4 (40) List of Figures Figure 1 Rear Panel Connectors (RX8310/BAS with RX83XX/HWO/IP/OUT) …… 9 Figure 2 Rear Panel Connectors (RX8315/BAS with RX83XX/HWO/IP/OUT) …… 9 Figure 3 Rear Panel Connectors (RX8330/BAS with RX83XX/HWO/IP/OUT) …. 10 Figure 4 Front Panel LEDs and Pushbuttons …………… …

  • Ericsson RX8330 — page 5

    Introduction 1 Introduction 1.1 Who Should Use this User Guide? This User Guide is written for operators/users of the RX8310, RX8315 and RX8330 Distribution Receivers to assist in installation and operation. Detailed information can be found in the Reference Guide companion document which is issued on CD. Warning! Do not remove the covers of this e …

  • Ericsson RX8330 — page 6

    Introduction 1.3 Hardware and Software Options See Table 2, 3, 4 and 5 for a list of hardware and software options available with the receivers. Detailed information is in the Reference Guide . T able 2 RX8310/RX8315/RX8330 Hardware Options Marketing Code Price Object Number Supply Object Number Description RX83XX/HWO/IP/OUT FAZ 101 0108/22 ROA 128 …

  • Ericsson RX8330 — page 7

    Introduction T able 4 RX8330 Hardware Options Marketing Code Price Objec t Number Supply Object Number Description RX83XX/HWO/RSECAM FAZ 101 0108/33 ROA 128 4418 Russi an SECAM Output Card T able 5 RX8330 Software Options Marketing Code Price Object Number Supply Object Number Description RX83XX/SWO/BISS FAZ 101 0108/30 FAT 102 0132 BISS Modes 1 an …

  • Ericsson RX8330 — page 8

    Installing the Equipment 2 Inst alling the Equipment 2.1 Introduction For best performance and reliability follow the instructions for site requirements and installation in the Reference Guide and only use installation accessories recommended by the manufacturers. Warning! Do not remove the covers of this equipment. Hazardous voltages are present w …

  • Ericsson RX8330 — page 9

    Installing the Equipment Warning! The Technical Earth is not a Protective earth for electric shock protection. This unit must be correctly earthed through the molded plug supplied. If the local mains supply does not have an earth conductor do not connect the unit. Contact Customer Services for advice. Before connecting the unit to the supply, check …

  • Ericsson RX8330 — page 10

    Installing the Equipment ETHE RNET 1- 2 TECHNICA L E A RT H ASI/ S DI O UT 1- 2 CVBS A LA RM AS I I N P U T AC P O W E R RF IN 1-4 AU D IO O UT (1 ) 1- 2 IP OU T 1 -2 CA INTERF ACE Figure 3 Rear Panel Connectors (RX8330/BAS with RX83XX/HWO/IP/OUT) Table 6 Types of Connector Type of Connector Description RF IN 1,2,3 & 4 F-type connectors for DVB …

  • Ericsson RX8330 — page 11

    Installing the Equipment 2.5 Connecting the Receiver to the Power Supply Warning! Do not overload wall outlets and extension cords as this can r esult in a risk of fire or electric shock. As no mains switch is fitted to this unit, ensure the local powe r supply is switched OFF before connecting the supply cord. The receiver is not fitted with an on …

  • Ericsson RX8330 — page 12

    Quick Start Guide: Connect- P ower — Configure 3 Quick S tart Guide: Connect-Power-Configure 3.1 Connecting the Receiver The following points should be noted when making signal connections to the receiver: • If you have an incoming satellite RF feed, this should be connected to the rear panel connector marked RF IN 1 — 4 . • If you have an inco …

  • Ericsson RX8330 — page 13

    Quick Start Guide: Connect- P ower — Configure 2. Switch on the AC power supply to the unit at the wall or rack outlet. Note: The RX8310/15/30 Receivers do NOT contain a power on/off switch. 3. After a short period of initialization the following screen is displayed on the Front Panel: INITIALIZING 4.3.2 (Bank 0) 4. During initialization, confirm t …

  • Ericsson RX8330 — page 14

    Quick Start Guide: Connect- P ower — Configure 8. Set the set the LNB power output level A description of each of these User Settings can be found in the Reference Guide . Note: If the unit has successful ly locked to the incoming feed, then the TS Lock value in menu Input should be LOCKED . 3.4 Selecting a Decode Service (Program) To select a deco …

  • Ericsson RX8330 — page 15

    Quick Start Guide: Connect- P ower — Configure • Alternative audio components may be selected from the service tab on the Web Control interface 3.7 Configuring for Single-serv ice Decryption When configuring for Single-service Decryption the following points shou ld be observed: • If the service selected for video decode contains encrypted comp …

  • Ericsson RX8330 — page 16

    Front P a nel C ontrol 4 Front Panel Control 4.1 Introduction The front panel display and keypad can be used to configure, control and monitor the receiver when an external control system is not used. Note: A list of receiver User Settings that may be viewed or changed via the front panel and those that may be viewed or changed via the external web …

  • Ericsson RX8330 — page 17

    Front P a nel C ontrol 4.3.2 LCD A 2-line x 40-character back-lit dot-matrix Liquid Crystal Display (LCD) displays various menus and settings. The menus and setting available will vary depending on which options have been enabled through the purchase of a suitable lice nse. 4.3.3 Arrow Pushbuttons Four arrow pushbuttons (or keys) are used to naviga …

  • Ericsson RX8330 — page 18

    Front P a nel C ontrol 4.4 Front Panel Menus An overview of the available Front Panel menus is shown below. The menus and settings available will vary depending on which receiver model is being used and which options have been enabled through the purchase of a suitable lice nse. Note: The menu structure is subject to change as further functionality …

  • Ericsson RX8330 — page 19

    Front P a nel C ontrol 4.4.1 Menu Structure The Front Panel menus and sub-menus, av ailable on the LCD, provide the configuration parameters that may be viewed, selected and/or modified. • System — Provides sub-menus for viewing/config uring the receiver hardware and access parameters. — Network – Enables the input and display of the addresses …

  • Ericsson RX8330 — page 20

    Front P a nel C ontrol — TS Feed Selection — Enables selection of the descrambling for the Transport Stream Feed. • Presets — Provides sub-menus for viewing, storing and retrieving up to 40 sets of input configuration parameters (tuning parameters and service selectio ns). — Preset State — Enables the current list of presets to be viewed. — Selec …

  • Ericsson RX8330 — page 21

    Web Br o w ser Control 5 W eb Browser Control 5.1 Introduction A personal computer (PC) running a Web Browser can be used to configure, control and monitor the receiver remotely. The following web browsers have been tested: • Microsoft Internet Explorer (This is the only browser supported by Ericsso n) • Mozilla Firefox (Functional but unsuppor …

  • Ericsson RX8330 — page 22

    Web Br o w ser Control Unit Model Number and Name About button Header Function Tabs Navi g ation Path Toolbar Main Web Page Results Frame Figure 6 Web Page Overview (T ypical) • Header – The header of the web page displays the Ericsson logo and the unit model number name. At the right-hand side of the header an About button which, when clicked, …

  • Ericsson RX8330 — page 23

    Web Br o w ser Control web page. When you switch between tabs, the browser remembers the path for each tab. • Navigation Path – The web pages are organized into a tree-like structur e, like the directory on a computer. The current complete navigation path is always displayed at the top of the web page, which shows the route taken to the current …

  • Ericsson RX8330 — page 24

    Web Br o w ser Control 5.3 W eb Pages 5.3.1 Status This web page shows a number of top-level parameters indicating the current status of the receiver. Figure 8 S t atus Web Page 5.3.2 Device Info The Device Info web page provides access to system-level settings for the receiver and can be used to enable the Front Panel Lockout Facility and initiate …

  • Ericsson RX8330 — page 25

    Web Br o w ser Control Figure 9 Device Info Web Page This page also provides buttons to the following further web pages: • Build – provides details of equipment build and version numbers. No user- editable fields. • Environment – provides details of the phy sical environment of the equipment such as temperature and fan speed. No user-editab …

  • Ericsson RX8330 — page 26

    Web Br o w ser Control 5.3.3 Alarms The Alarms web page provides access to the alarms settings for the receiver. The contents of this page are composed mainly of fields with drop-down menus which allow the setting or masking of various alarms and check boxes which can be used to activate relay mapping. Two of the al arm fields, namely C/N (Carrier- …

  • Ericsson RX8330 — page 27

    Web Br o w ser Control Figure 10 Alarms W eb Page 5.3.4 Customization Web Page The Customization web page provides acce ss to the list of licenses enabled on the equipment and to enable further licenses (as purchased) by entering the custom key provided. Figure 1 1 Customization W eb Page 5.3.5 CA The CA web page allows viewing and modification of …

  • Ericsson RX8330 — page 28

    Web Br o w ser Control Figure 12 CA W eb Page 5.3.6 Input The Input Web Page provides access to the parameters of the various inputs to the receiver. The page, which is displayed, depends on which Input card is fitted. The options are: • Satellite Input Card The Input page displays parameters for input feed lock status and bit rate, primary and s …

  • Ericsson RX8330 — page 29

    Web Br o w ser Control Figure 13 Input Web Page Click on the Satellite Input button on the Input page to display a further sub page. Figure 14 Input > SA T Input Sub Page The only field which may be edited by the user is the RF Selection field which allows selection of the appropriate RF Input. There are also four Configuration buttons which all …

  • Ericsson RX8330 — page 30

    Web Br o w ser Control 5.3.7 Service Plus The Service Plus web page provides access to the various encryption and encoding services available to the receiver. A Se rvice Control table is displayed showing which services are available. The only use r-editable fields in this table are the Decrypt and Decode checkboxes. The user can select Decry pt , …

  • Ericsson RX8330 — page 31

    Web Br o w ser Control Figure 16 Decode Web Page 5.3.9 Output The Output web page provides access to the output feed parameters of the receiver. EN/LZT 790 0008/1 R1A 2011-03 -30 31 (40) …

  • Ericsson RX8330 — page 32

    Web Br o w ser Control Figure 17 Output Web Page 5.3.10 Download The Download web page provides access to the over air download status of the receiver. There are no user-editable fields on this page. EN/LZT 790 0008/1 R1A 2011-03 -30 32 (40) …

  • Ericsson RX8330 — page 33

    Web Br o w ser Control Figure 18 Download Web Page 5.3.11 SNMP This page gives access to the Simple Network Management Protocol (SNMP) parameters for the receiver, including protocol selection and MIB parameters. Figure 19 SNMP W eb Page 5.3.12 Presets The Presets web page gives access to a list of 40 preset configurations. This feature may be used …

  • Ericsson RX8330 — page 34

    Web Br o w ser Control Figure 20 Presets W eb Page 5.3.13 Save/Load The Save/Load web page provides a range of configuration download and upload facilities, including saving and restoring unit confi guration, saving unit MIB files, saving alarm log files and saving splice log files. EN/LZT 790 0008/1 R1A 2011-03 -30 34 (40) …

  • Ericsson RX8330 — page 35

    Web Br o w ser Control Figure 21 Save/Load Web Page 5.3.14 Help The Help web page gives access to a Web Interface User Guide which provides a brief description of the interface functionality. Figure 22 Help Web Page EN/LZT 790 0008/1 R1A 2011-03 -30 35 (40) …

  • Ericsson RX8330 — page 36

    Equipment P a ckaging 6 Equipment Packaging 6.1 Packaging S t atement The outer carton and any cardboard inserts are made from 82% recycled material and are fully recyclable. The Stratocell ® or Ethafoam 220 ® polyethylene foam inserts can be easily recycled with other low density polyethylene (LDPE) materials 6.2 Packaging Markings The symbols p …

  • Ericsson RX8330 — page 37

    Materials Declarations 7 Materials Declarations 7.1 Overview Ericsson products are designed and manufactured in keeping with good environmental practice. Our component and materials selection policy prohibits the use of a range of potentially hazardous materials. In addition, we comply with relevant environmental legislation. 7.2 For the European U …

  • Ericsson RX8330 — page 38

    Disposal of this Equipment 8 Disposal of this Equipment 8.1 General Dispose of this equipment safely at the end of its life. Local codes and/or environmental restrictions may affect its disposal. Regulations, policies an d/or environmental restrictions differ throughout the world. Contact your local jurisdiction or local authority for specific advi …

  • Ericsson RX8330 — page 39

    Re c y cling 9 Recycling Ericsson SA TV Recycling has a process facility that enables customers t o return Old and End-of-Life Products for recycling if it is required. Ericsson provides assistance to customers and recyclers thr ough our Ericsson and SATV Recycling eBusiness Portal. This can be reached at: https://ebusiness.ericsson .net/ . To gain …

  • Ericsson RX8330 — page 40

    Re c y cling EN/LZT 790 0008/1 R1A 2011-03 -30 40 (40) …

Краткое содержание страницы № 1

RX8310/15/30 Distribution Receivers
Software Version 4.3.2

USER GUIDE

EN/LZT 790 0008/1 R1A

Краткое содержание страницы № 2

RX8310/15/30 Distribution Receivers Copyright © Copyright Ericsson AB 2011. All rights reserved. Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. Ericsson shall have no liability for any error or damage of any kind resulting from the use of this document. Customer Services Eur

Краткое содержание страницы № 3

Contents Contents 1 Introduction……………………………………………………………………………….. 5 1.1 Who Should Use this User Guide?…………………………………………………. 5 1.2 What Equipment is Covered by this User Guide? …………………………….. 5 1.3 Hardware and Software Options ……………………………………………………. 6 2 Installing the Equipment………………………………………………..

Краткое содержание страницы № 4

Contents List of Figures Figure 1 Rear Panel Connectors (RX8310/BAS with RX83XX/HWO/IP/OUT) ……9 Figure 2 Rear Panel Connectors (RX8315/BAS with RX83XX/HWO/IP/OUT) ……9 Figure 3 Rear Panel Connectors (RX8330/BAS with RX83XX/HWO/IP/OUT) ….10 Figure 4 Front Panel LEDs and Pushbuttons……………………………………………….16 Figure 5 Front Panel Menus………………………………………………………………………18 Figure 6 Web Page Overview (Typi

Краткое содержание страницы № 5

Introduction 1 Introduction 1.1 Who Should Use this User Guide? This User Guide is written for operators/users of the RX8310, RX8315 and RX8330 Distribution Receivers to assist in installation and operation. Detailed information can be found in the Reference Guide companion document which is issued on CD. Warning! Do not remove the covers of this equipment. Hazardous voltages are present within this equipment and may be exposed if the covers are removed. Only Ericsson trained and app

Краткое содержание страницы № 6

Introduction 1.3 Hardware and Software Options See Table 2, 3, 4 and 5 for a list of hardware and software options available with the receivers. Detailed information is in the Reference Guide. Table 2 RX8310/RX8315/RX8330 Hardware Options Marketing Code Price Object Supply Object Description Number Number RX83XX/HWO/IP/OUT FAZ 101 0108/22 ROA 128 3646 Dual Gigabit IP Transport Stream Output Card RX8XXX/CABLE/XLR FAZ 101 0108/24 RPM 901 364 XLR Terminal Audio Break-out Cable RX8XXX/

Краткое содержание страницы № 7

Introduction Table 4 RX8330 Hardware Options Marketing Code Price Object Supply Object Description Number Number RX83XX/HWO/RSECAM FAZ 101 0108/33 ROA 128 4418 Russian SECAM Output Card Table 5 RX8330 Software Options Marketing Code Price Object Supply Object Description Number Number RX83XX/SWO/BISS FAZ 101 0108/30 FAT 102 0132 BISS Modes 1 and E RX83XX/SWO/BISS/MSD FAZ 101 0108/16 FAT 102 0133 BISS Modes 1 and E Multi-Service Decryption RX83XX/SWO/DIR5/MSD FAZ 101 0108/3 FAT 102

Краткое содержание страницы № 8

Installing the Equipment 2 Installing the Equipment 2.1 Introduction For best performance and reliability follow the instructions for site requirements and installation in the Reference Guide and only use installation accessories recommended by the manufacturers. Warning! Do not remove the covers of this equipment. Hazardous voltages are present within this equipment and may be exposed if the covers are removed. Only Ericsson trained and approved service engineers are permitted to se

Краткое содержание страницы № 9

Installing the Equipment Warning! The Technical Earth is not a Protective earth for electric shock protection. This unit must be correctly earthed through the molded plug supplied. If the local mains supply does not have an earth conductor do not connect the unit. Contact Customer Services for advice. Before connecting the unit to the supply, check the supply requirements in Annex B of the Reference Guide. 2.4 Rear Panel Connectors Always use the specified cables supplied for signal i

Краткое содержание страницы № 10

Installing the Equipment RF IN 1-4 IP OUT 1-2 AUDIO OUT (1) AC POWER 1-2 CA ASI/SDI OUT 1-2 CVBS ASI INPUT ETHERNET 1-2 ALARM TECHNICAL INTERFACE EARTH Figure 3 Rear Panel Connectors (RX8330/BAS with RX83XX/HWO/IP/OUT) Table 6 Types of Connector Type of Connector Description RF IN 1,2,3 & 4 F-type connectors for DVB or DVB-S2 modulated input feed. IP OUT 1 & 2 8-way RJ-45 connectors for 1000BaseT IP output feed. AUDIO OUT 1 & 2 9-way male D-type connectors for analogue

Краткое содержание страницы № 11

Installing the Equipment 2.5 Connecting the Receiver to the Power Supply Warning! Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. As no mains switch is fitted to this unit, ensure the local power supply is switched OFF before connecting the supply cord. The receiver is not fitted with an on/off switch. Ensure that the socket-outlet is installed near the equipment so that it is easily accessible. Failure to isolate the equipment

Краткое содержание страницы № 12

Quick Start Guide: Connect-Power-Configure 3 Quick Start Guide: Connect-Power-Configure 3.1 Connecting the Receiver The following points should be noted when making signal connections to the receiver: • If you have an incoming satellite RF feed, this should be connected to the rear panel connector marked RF IN 1 — 4. • If you have an incoming ASI feed, this should be connected to the ASI Input. • Decoded PAL or NTSC video is output on connectors CVBS 1 and CVBS 2. These outputs are i

Краткое содержание страницы № 13

Quick Start Guide: Connect-Power-Configure 2. Switch on the AC power supply to the unit at the wall or rack outlet. Note: The RX8310/15/30 Receivers do NOT contain a power on/off switch. 3. After a short period of initialization the following screen is displayed on the Front Panel: INITIALIZING 4.3.2 (Bank 0) 4. During initialization, confirm that the Status LED is on and all Up, Down, Left, Right, Edit and Save pushbuttons are lit. 3.2.2 Power Up Operating Modes When the equipment

Краткое содержание страницы № 14

Quick Start Guide: Connect-Power-Configure 8. Set the set the LNB power output level A description of each of these User Settings can be found in the Reference Guide. Note: If the unit has successfully locked to the incoming feed, then the TS Lock value in menu Input should be LOCKED. 3.4 Selecting a Decode Service (Program) To select a decode service: 1. Navigate to the Service menu. For incoming feeds containing only a single service the service may be selected automatically dependi

Краткое содержание страницы № 15

Quick Start Guide: Connect-Power-Configure • Alternative audio components may be selected from the service tab on the Web Control interface 3.7 Configuring for Single-service Decryption When configuring for Single-service Decryption the following points should be observed: • If the service selected for video decode contains encrypted components these components will automatically be decrypted by the unit. • The outgoing feed from the unit will contain these decrypted components provid

Краткое содержание страницы № 16

Front Panel Control 4 Front Panel Control 4.1 Introduction The front panel display and keypad can be used to configure, control and monitor the receiver when an external control system is not used. Note: A list of receiver User Settings that may be viewed or changed via the front panel and those that may be viewed or changed via the external web browser interface can be found in the Reference Guide. 4.2 Receiver Front Panel LCD EDIT LEFT UP USB Connector Status LED SAVE DOWN RIGH

Краткое содержание страницы № 17

Front Panel Control 4.3.2 LCD A 2-line x 40-character back-lit dot-matrix Liquid Crystal Display (LCD) displays various menus and settings. The menus and setting available will vary depending on which options have been enabled through the purchase of a suitable license. 4.3.3 Arrow Pushbuttons Four arrow pushbuttons (or keys) are used to navigate through the front panel LCD menus. Each arrow pushbutton is backlit by an integral LED when active, indicating that a further choice or act

Краткое содержание страницы № 18

Front Panel Control 4.4 Front Panel Menus An overview of the available Front Panel menus is shown below. The menus and settings available will vary depending on which receiver model is being used and which options have been enabled through the purchase of a suitable license. Note: The menu structure is subject to change as further functionality is added. SWITCH ON 1.1 Network Menu Boot Screen INITIALIZING — 1.1.1 IP1 4.3.2 (Bank 0) — 1.1.2 MAC1 — 1.1.3 IP2 — 1.1.4 MAC2

Краткое содержание страницы № 19

Front Panel Control 4.4.1 Menu Structure The Front Panel menus and sub-menus, available on the LCD, provide the configuration parameters that may be viewed, selected and/or modified. • System — Provides sub-menus for viewing/configuring the receiver hardware and access parameters. — Network – Enables the input and display of the addresses required to communicate with the receiver. Access to the receiver Status page is also available from this sub-menu. — Build — Provides version and I

Краткое содержание страницы № 20

Front Panel Control — TS Feed Selection — Enables selection of the descrambling for the Transport Stream Feed. • Presets — Provides sub-menus for viewing, storing and retrieving up to 40 sets of input configuration parameters (tuning parameters and service selections). — Preset State — Enables the current list of presets to be viewed. — Select/Save Preset — Enables selection and saving of presets. More detail on all user settings may be found in the Reference Guide. EN/LZT 790 00

Distribution Receiver

The Ericsson RX8330 Distribution Receiver extends the RX8300 series of Integrated Receiver Decoders by

providing feature-rich multi-format standard definition (SD) decoding capability with high quality SDI output

for video distribution applications. The RX8330 gives the user access to the latest compression and

transmission technologies to allow for the most cost-effective and bandwidth transmissions possible while

ensuring the highest standards of reliability and video quality.

The RX8330 offers both ASI and the latest DVB-S2 capable satellite input interfaces. As security of content

is always of paramount importance, compatibility with popular CA systems including DVB Common

Interface is provided. The RX8330 shows its true class through its capability for multi-format decoding of all

SD 4:2:0 video standards combined with high quality SDI digital video and analog video outputs. This

capability is further enhanced by the RX8330’s ability to receive, and down-convert HD video to SD

providing an SD output for broadcast or monitoring. Additionally for systems that stay in the compressed

domain, decrypted transport streams can be handed off into digital networks through a choice of both ASI or

optional IP output interfaces.

The feature-rich specification of the RX8330 provides the capability and flexibility that places the receiver as

the key link in the broadcast chain for applications from content distribution and turn-around to critical

network monitoring.

PRODUCT OVERVIEW

The Perfect Choice for a Large Network

The RX8330 is the perfect receive device for distribution of video services

throughout a large network. The RX8330 provides the most up-to-date

feature-set, combining maximum transmission efficiency with easy remote

management of the receiver population.

Increased Distribution Capacity and Efficiency

The RX8330 in combination with Ericsson’s MPEG-4 AVC encoders and

PREKOR™ Dynamic Pre-correction System leads to a highly efficient

video distribution system. Combined with the additional 30 percent

increase in channel capacity of DVB-S2 the RX8330 allows operators to

achieve three times the amount of content through a transponder.

Multi-format Decoding — a «Safe Choice» for the Future

The RX8330 decodes all major SD video formats in use today providing

complete flexibility for daily operations. The versatility that the RX8330

decoder provides makes it a «safe choice» for companies that are

beginning to transmit MPEG-4 AVC SD but also continue to work in

MPEG-2 SD. With the RX8330 they can migrate at their own pace.

Simplified Control and Lower Cost of Operations

Organizations with large populations of RX8330 receivers and other

Ericsson receivers can simplify control by integrating with Director by

Ericsson. Director provides remote, over-air, single-view control from a

central location, reducing the need for on-site local operators.

Ericsson RX8330

BASE UNIT FEATURES

RX8330 – Distribution Receiver (RX8330/BAS, FAZ 101 0108/1)

The following features are available as standard:

Four input DVB-S QPSK satellite demodulator

Transport stream input with ASI connection

Dual switchable ASI/SDI output (SDI via additional license)

Single service DVB Common Interface CA support

Single service BISS CA support

Director single service decryption, Ooer-air control and software

download

Front panel and Web browser control, with alarm relay

SCTE 35 controlled contact closures for ad-insertion signaling

Optional features include:

DVB-S2 QPSK, 8PSK and 16APSK* demodulation

DVB-S2 VCM mode support*

Transport stream over IP output

Multi-service decryption via Pro CAMs

Multi-service BISS decryption

MPEG-2 SD 4:2:0 video decoding

MPEG-2 HD 4:2:0 down-conversion

MPEG-4 AVC SD video decoding

MPEG-4 AVC HD down-conversion

®

Two stereo pair Dolby

Digital audio decoding with 5.1 to 2.0 down-

mixing

AAC audio decoding with 5.1 to 2.0 down-mixing

SDI digital video output

MPE IP data de-encapsulation

Single service filtering and PID remapping

08-2012-v6

RX8310/15/30 Distribution Receivers

Software Version 4.3.2

USER GUIDE

EN/LZT 790 0008/1 R1A  



Руководстве по эксплуатации Ericsson RX8330 — вам приходилось его терять? Поскольку вы попали сюда, наверняка с вами это случилось. Но вы не единственный человек, сталкивающийся с проблемами с хранением руководства по эксплуатации всех домашних устройств. Ниже несколько советов, касающихся того, зачем собирать руководства по эксплуатации.

Руководстве по эксплуатации Ericsson RX8330 это определенный вид технической документации, являющейся неразлучным элементом каждого устройства, которое мы приобретаем. Они отличаются между собой количеством информации, которую можно найти на тему данного устройства: напр. Ericsson RX8330. Конечно же, если производитель считает что необходимо передать нам большее количество информации, касающейся устройства Ericsson RX8330, то стоит ее хоть раз прочитать — в начале, сразу же после покупки данной вещи. Однако мы считаем, что инструкции должны заключать самую важную, наиболее необходимую информацию о Ericsson RX8330, так, чтобы не отнимать желания пользователя прочесть ее уже в самом начале. Несомненно, если устройство Ericsson RX8330 имеет много продвинутых функций, неизбежно большое количество информации в содержании этого документа.

Które из информации в инструкции Ericsson RX8330 необходимо обязательно прочитать?

  • Информацию, касающуюся правильного использования и ухода за устройством Ericsson RX8330 — нам необходимо ознакомиться с основными правилами, чтобы в случае проблем с устройством сервисный центр не отказал нам в гарантийном обслуживании, из-за неправильного использования
  • Информация, касающаяся самых частых проблем с Ericsson RX8330 и способы их решения
  • Информация, касающаяся гарантии устройства Ericsson RX8330 и ближайших сервисных центров, способных починить устройство в соответствии с рекомендациям производителя Ericsson

Как хранить инструкции дома?

Хорошей идеей является предназначение одного ящика, в котором бы хранилась инструкция Ericsson RX8330 а также всех других домашних устройств которыми мы пользуемся. Тогда значительно легче вам будет ее найти, чем искать в родных коробках, которые наверняка уже выбросили вы, или другие домочадцы. Раз в год достаточно просмотреть ящик и выбросить инструкции, которые касаются устройств, которыми вы уже не пользуетесь. Таким образом вы избежите хранения ненужных документов, а останутся только актуальные. Вы можете также скачать и распечатать инструкцию Ericsson RX8330 чтобы разместить ее в своем ящике.

Похожие инструкции


IP Transport Stream Output

(RX83XX/HWO/IP/OUT, FAZ 101 0108/22)

Encapsulation of transport stream output into IP multicast

MPTS or single SPTS output stream

2x Gigabit Ethernet RJ-45 interfaces

Russian SECAM Output

(RX83XX/HWO/RSECAM, FAZ 101 0108/33)

High quality Russian SECAM output

Mutually exclusive with IP TS output option

SOFTWARE OPTIONS

Input Options

The RX8330 comes with DVB-S, QPSK support as standard. The unit can

also be licensed to support the DVB-S2 satellite transmission standard.

DVB-S2 QPSK License

(RX83XX/SWO/DVBS2/QPSK, FAZ 101 0108/6)

Adds DVB-S2 QPSK capability to DVB-S2 input option card

DVB-S2 8PSK License

(RX83XX/SWO/DVBS2/8PSK, FAZ 101 0108/4)

Adds DVB-S2 QPSK, 8PSK capability to DVB-S2 input option card

DVB-S2 16APSK License (RX83XX/SWO/DVBS2/16APSK)*

Adds DVB-S2 QPSK, 8PSK and 16APSK capability to DVB-S2 input

option card

DVB-S2 Low Symbol Rate License

(RX83XX/SWO/DVBS2/LSYM, FAZ 101 0108/5)

Enables DVB-S2 symbol rate of 1 Msym/s to 5 Msym/s

DVB-S2 Multi-Transport Stream License

(RX83XX/SWO/DVBS2/VCM)*

Provides DVB-S2 Variable Coding and Modulation support

Single TS output

Null Packet Detection Redundancy Switching

(RX83XX/SWO/NULL, FAZ 101 0108/17)

Redundancy switching from primary to secondary input triggered by

presence of a user defined % of null packets in the incoming stream

Decoding Options

The RX8330 is designed to support a range of video decoding standards

MPEG-2 SD Decoding

(RX83XX/SWO/MPEG2/SD, FAZ 101 0108/10)

Enables MPEG-2 SD 4:2:0 decoding

MPEG-2 HD Down-conversion

(RX83XX/SWO/MPEG2/HD, FAZ 101 0108/9)

Enables MPEG-2 SD and HD 4:2:0 decoding

HD video is down-converted and presented as SD on CVBS output

MPEG-4 AVC SD Decoding

(RX83XX/SWO/MP2/MP4/SD, FAZ 101 0108/12)

Enables MPEG-2 and MPEG-4 AVC SD 4:2:0 video decoding

MPEG-4 AVC HD Down-conversion

(RX83XX/SWO/MP2/MP4/SD/HD, FAZ 101 0108/11)

Enables MPEG-2 SD and HD, MPEG-4 AVC SD and HD 4:2:0 decoding

HD video is down-converted and presented as SD on CVBS output

Video Output Options

The RX8330 is always supplied with analog composite video output. The

RX8330can additionally be enabled with this option.

SDI Digital Video Output (RX83XX/SWO/SDI, FAZ 101 0108/35)

Enables SDI digital video output on RX8330 unit

Ericsson RX8330 Distribution Receiver

Screw Terminal Audio Break-Out Cable

(RX8XXX/CABLE/SCRTRM, FAZ 101 0108/23)

Provides screw terminal connections for analog audio output

1x stereo pair per breakout cable

XLR Terminal Audio Break-Out Cable

(RX8XXX/CABLE/XLR, FAZ 101 0108/24)

Provides XLR terminal connections for analog audio output

1x stereo pair per breakout cable via 2x XLR connectors

Security Options

Password Protection of Web Browser

(RX83XX/SWO/PW, FAZ 101 0108/29)

Enables password protection feature of web browser control

Audio Options

®

Dolby

Digital Decode (RX83XX/SWO/AC3, FAZ 101 0108/28)

Enables decoding of Dolby Digital Audio

2x 2.0 (stereo) decoding

2x 5.1 down-mix to 2.0 (stereo)

AAC Decode (RX83XX/SWO/AAC, FAZ 101 0108/2)

Enables decoding of AAC-LC and HE-AAC

2x 2.0 (stereo) decoding

2x 5.1 down-mix to 2.0 (stereo)

Conditional Access Options

Multi-Service CAM Decryption

(RX83XX/SWO/MSD, FAZ 101 0108/13)

Decrypt multiple services via professional CAMs

Simultaneously decrypt up to 10 services or 24 PIDs max

Director by Ericsson Multi-service Decryption

(RX83XX/SWO/DIR5/MSD, FAZ 101 0108/3)

Director multi-service decryption,

Director over-air control and software download

BISS Multi-service CA

(RX83XX/SWO/BISS/MSD, FAZ 101 0108/16)

Multi-service decryption for BISS

Support for multiple BISS keys

Stream Processing Options

Single Service Filtering

(RX83XX/SWO/SING/SERVFILT, FAZ 101 0108/15)

Filter multiple services to output a single service

Re-map PIDs for the outgoing service

Multi-Service Filtering

(RX83XX/SWO/MULT/SERVFILT, FAZ 101 0108/14)

Filter N multiple incoming services to M outgoing services

Re-map PIDs for a single service

CBR MPTS transport stream output

Service splitting for multiple IP SPTS output

SMPTE 2022M Pro-MPEG FEC License on IP TS Output

(RX83XX/SWO/IP/OUT/PROMPEG, FAZ 101 0108/8)

Enables SMPTE 2022M Pro-MPEG FEC capability for the IP output

card

Requires IP output card

Data Options

High Speed Data Output (RX83XX/SWO/IP/DATA, FAZ 101 0108/7)

MPE based data de-encapsulation of IP data

Requires IP TS output option

08-2012-v6

  • Главная
  • Ericsson

  • Спутниковые радиостанции

  • RX8330

На этой странице вы найдёте полный список документов на Спутниковые радиостанции Ericsson RX8330.

Выберите необходимый PDF файл.

  • Спутниковые радиостанции Ericsson RX8330 Инструкция по эксплуатации

    Спутниковые радиостанции
    Ericsson RX8330 Инструкция по эксплуатации

    Тип файла
    PDF

    Размер
    73 Kb

    Кол-во страниц
    3

    Просмотров
    960

    Download / Read online

  • 1

Другие Ericsson Спутниковые радиостанции

  • Ericsson RX8330 Инструкция по эксплуатации

    PDF файлов
    1

    Просмотров
    1602

  • Ericsson Distribution Receiver RX8300 Инструкция по эксплуатации

    PDF файлов
    1

    Просмотров
    1317

Другие устройства Ericsson

  • Принтеры
    Ericsson STYLUS PRO 7700 Инструкция по эксплуатации

    PDF файлов
    1

    Просмотров
    21269

  • Телефоны
    Ericsson Dialog 3213 Инструкция по эксплуатации

    PDF файлов
    1

    Просмотров
    19894

  • Принтеры
    Ericsson STYLUS PRO 4900 Инструкция по эксплуатации

    PDF файлов
    1

    Просмотров
    17347

  • Принтеры
    Ericsson SP4900HDR Инструкция по эксплуатации

    PDF файлов
    1

    Просмотров
    16477

  • Принтеры
    Ericsson SP4900DES Инструкция по эксплуатации

    PDF файлов
    1

    Просмотров
    16295

  • Телефоны
    Ericsson DIALOG 4422 Инструкция по эксплуатации

    PDF файлов
    1

    Просмотров
    14268

Вопросы

  • слабая батарея

    Ноутбуки

    Acer

    1310

    Alex 12.02.2016 17:26

Ранее вы смотрели

Производители

Astone Holdings Pty

Desa Tech

Fluke

Gentek

Simple Mobile

Tektronix

Tesco

Wayne

Withings

XiNCOM

Типы устройств

Угольные грили

Фильтры для плавательного бассейна

Костровые чаши

Шкафы для подогрева посуды

Фанкойлы (Вентиляторные доводчики)

Наладонники Pocket Viewer

Автоматические кофемашины

Продукты MACRO-интерфейса

Пылесосы

Дымовые и газовые сигнализации

Устройства

Atlantis A02-F8

Casio Keyboard WK200

ColdTech JDD-80

Diamond Audio Technology CM3 08D4

Hamilton Beach 26030

Hotpoint LEB326

Linear 9520 Series

OPTI-UPS High-Frequency Online UPS DS3000E

Sharp 32U-S50B

Technicolor — Thomson 608

freeuserguide.ru
About Us
Contacts
Disclamers
Privacy Policy

Эта страница полезна для вас? Поделитесь ссылкой:

Понравилась статья? Поделить с друзьями:
  • Erectalis египет инструкция по применению на русском языке
  • Ericsson dialog 4222 инструкция на русском
  • Ertes 72 инструкция на русском
  • Equation wap 117eah инструкция скачать
  • Ersag массажный крем инструкция по применению