Jbl onbeat venue lt инструкция

JBL OnBeat™ VENUE LT

Quick Setup Guide

Welcome

Thank you for purchasing the JBL OnBeat™ Venue LT speaker dock. This quick setup guide will show you how to connect and set up your dock.

CONNECTIONS

1.If you are going to use your OnBeat Venue LT with another audio source, plug one end of a 3.5mm (1/8″) stereo cable (not supplied) into the OnBeat Venue LT’s Aux In connector, and plug the other end into the audio source’s audio out or headphone out connector.

2.Plug the OnBeat Venue LT’s power supply into the Power connector on the unit and into a working AC power outlet. The OnBeat Venue LT will automatically turn on and go into the Bluetooth pairing mode (the Bluetooth LED will be flashing blue).

Power Aux

Connector Input

2

• JBL OnBeat   VenUe Lt
  ™
  Quick Setup Guide
  WeLcOme
  Thank you for purchasing the JBL OnBeat  Venue LT speaker dock. This quick setup
  ™
  guide will show you how to connect and set up your dock.
  cOnnectIOnS
  1. If you are going to use your OnBeat Venue LT with another audio source, plug one end of
  a 3.5mm (1/8") stereo cable (not supplied) into the OnBeat Venue LT’s Aux In connector,
  and plug the other end into the audio source’s audio out or headphone out connector.
  2. Plug the OnBeat Venue LT’s power supply into the Power connector on the unit and into
  a working AC power outlet. The OnBeat Venue LT will automatically turn on and go into
  the Bluetooth pairing mode (the Bluetooth LED will be flashing blue).
  Power     Aux
  Connector  Input

• PLACEMENT
  Place OnBeat Venue LT on a shelf or table with the rear of its enclosure is at least 3"
  (76mm) away from a wall or other surface to allow the bass ports to operate properly.
  CONTROLS AND INDICATORS
  Dock Input
  LED
  Movie   Aux Input     Bluetooth
  Button    LED         LED
  Bass Boost        Source           Power        Volume Up/Down
  Button         Button          Button        Buttons
  Docking Slide (open)
  LT Docking Connector
  Bass Boost button: Press this button to enhance the bass performance. The button’s
  LED will illuminate when Bass Boost is on.
  Movie button:  Press this button to activate the Movie EQ mode, which creates an
  extra-wide sound field to compliment films and other video media. The button’s LED will
  illuminate when the Movie mode is on.
  Source button: Press this button to cycle through the audio sources: Bluetooth, docked
  device and Aux Input. The input LED for the active source will illuminate.
  •  If you begin to stream audio from a paired Bluetooth device or play audio from a device
  connected to  the dock while another source is  playing,  the OnBeat Venue  LT will
  automatically switch to the new source.
  Aux Input LED: This LED illuminates when the Aux Input is the active source.
  Dock Input LED: This LED illuminates when the docked device is the active source.
  Bluetooth  LED:  This  LED  flashes  blue  when  the  OnBeat  Venue  LT  is  in  the  Bluetooth
  pairing mode, and turns solid blue when it has successfully paired with a Bluetooth device.
  Power button: When the OnBeat Venue LT is on, press the Power button to put it into the
  standby mode. The button’s LED will illuminate solid amber when the unit is in standby.
  When the OnBeat Venue LT is in standby, press the Power button to turn it on. The button’s
  LED will illuminate solid white when the unit is on.
  2

• When the OnBeat Venue LT is in the standby mode it will automatically turn on when it
  detects audio playing from a Bluetooth-connected device or from a docked device.
  When the OnBeat Venue LT is on, it will automatically enter the standby mode after 10
  minutes of inactivity (no audio input and no user-control operation).
  Note: When the OnBeat Venue LT enters the standby mode it will also bring a docked
  device into standby mode.
  Volume Up/Down buttons: Press these buttons to raise and lower the OnBeat Venue LT’s
  volume. To mute the sound, press both buttons at the same time. (The Power button LED
  will flash white when the sound is muted.) To restore the sound press either Volume button
  or both buttons together.
  Docking slide: Press in on the JBL logo to open the docking slide and pull the slide all
  the way open.
  Docking connector: Place your device onto the docking slide so that it is firmly seated
  on the docking connector.
  Made for
  iPhone 5
  iPod nano 7th generation
  iPod touch 5th generation
  Note: We recommend that you disable the”Shake to Shuffle” feature on your iPod nano,
  iPod touch and iPhone before docking the device on the OnBeat Venue LT.
  BLUETOOTH WIReLeSS StReamInG
  To wirelessly stream audio to the OnBeat Venue LT from a Bluetooth-enabled device:
  1.  If the OnBeat Venue LT’s Bluetooth LED is not flashing blue, press the Source button
  until the Bluetooth LED begins flashing blue.
  2.  Place the Bluetooth-capable device in the pairing mode. Use the device’s Bluetooth
  pairing menu to pair with OnBeat Venue LT. (If the device requires a pairing code, use
  0000.)
  3.  When OnBeat Venue LT’s Bluetooth LED illuminates blue continually, it is paired with
  the device and you can stream audio via Bluetooth from the device to the OnBeat
  Venue LT.
  To disconnect the Bluetooth device, press and hold the Source button. To pair OnBeat Venue
  LT with a different Bluetooth-enabled device, repeat Steps 2 and 3 with the new device.
  www.jbl.com  3

• 1
• 2
• 3
• 4