Nad c658 инструкция на русском

1.Read instructions — All the safety and operating instructions should be read before the product is operated.

2.Retain instructions — The safety and operating instructions should be retained for future reference.

3.Heed Warnings — All warnings on the product and in the operating instructions should be adhered to.

4.Follow Instructions — All operating and use instructions should be followed.

5.Cleaning — Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6.Attachments — Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7.Water and Moisture — Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8.Accessories — Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. Cart — A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10.Ventilation — Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating.

These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11.Power Sources — This product should be operated only from the type of power source indicated on the marking label and connected to a MAINS socket outlet with a protective earthing connection. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

12.Power-Cord Protection — Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

13.Mains Plug — Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

14.Outdoor Antenna Grounding — If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

15.Lightning — For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16.Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17.Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

18.Flame Sources — No naked flame sources, such as lighted candles, should be placed on the product.

19.Object and Liquid Entry — Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

20.Headphones — Excessive sound pressure form earphones and headphones can cause hearing loss.

21.Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the product.

c.If the product has been exposed to rain or water.

d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e.If the product has been dropped or damaged in any way.

f.When the product exhibits a distinct change in performance-this indicates a need for service.

22.Replacement Parts — When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

23.Battery Disposal — When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.

24.Safety Check — Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

25.Wall or Ceiling Mounting — The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

WARNING

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

THE EQUIPMENT MUST BE CONNECTED TO AN EARTHED MAINS SOCKET-OUTLET.

CAUTION REGARDING PLACEMENT

To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) than is equal to, or greater than shown below.

Left and Right Panels: 10 cm Rear Panel: 10 cm

Top Panel: 10 cm

FCC STATEMENT

This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio TV technician for help.

CAUTION

•Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user’s authority to operate this equipment.

•This device complies with Part 15 of the FCC Rules / Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and

2 This device must accept any interference received, including interference that may cause undesired operation.

•Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

•To prevent electric shock, match wide blade of plug to wide slot, fully insert.

•Marking and rating plate can be found at the rear panel of the apparatus.

•To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus.

•Mains plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.

•Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

•Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

•An appliance with a protective earth terminal should be connected to a mains outlet with a protective earth connection.

MPE REMINDER

To satisfy FCC/IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.

IF IN DOUBT CONSULT A COMPETENT ELECTRICIAN.

This product is manufactured to comply with the radio interference requirements of EEC DIRECTIVE 2004/108/EC.

NOTES ON ENVIRONMENTAL PROTECTION

At the end of its useful life, this product must not be disposed of with

regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s manual and packaging point this out.

The materials can be reused in accordance with their markings. Through re-use, recycling of raw materials, or other forms of recycling of old products, you are making an important contribution to the protection of our environment.

Your local administrative office can advise you of the responsible waste disposal point.

RECORD YOUR MODEL NUMBER (NOW, WHILE YOU CAN SEE IT)

The model and serial number of your new C 658 are located on the back of the cabinet. For your future convenience, we suggest that you record these numbers here:

Model number : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Serial number :. . . . . . . . . . . . . . . . . . . .

INTRODUCTION

WHAT’S IN THE BOX. . . . . . . . . . . . . . . . . . . . . . . . . .4 CHOOSING A LOCATION . . . . . . . . . . . . . . . . . . . . . . . 4 RESTORING C 658 TO FACTORY DEFAULT SETTINGS. . . . . . . . . .4

GETTING STARTED. . . . . . . . . . . . . . . . . . . . . . . . 5

QUICK SETUP GUIDE. . . . . . . . . . . . . . . . . . . . . . . . . 5

MDC CLASSIC UPGRADE SLOTS. . . . . . . . . . . . . . . . . . . .9 MDC HDM-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

USING THE SR 9 REMOTE CONTROL. . . . . . . . . . . . . . . .10

USING THE SR 9 REMOTE CONTROL LIBRARY. . . . . . . . . . . . 12

OPERATION

USING C 658. . . . . . . . . . . . . . . . . . . . . . . . . . .13

REFERENCE

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . .21

Packed with your C 658 you will find

•Two detachable mains power cord

•SR 9 remote control with 2 AA batteries

•USB MIC Sound Adaptor

•Mic Assembly with Ferrite Base

•Bluetooth and Wi-Fi antennas

•Quick Setup Guide

SAVE THE PACKAGING

Please save the box and all of the packaging in which your C 658 arrived. Should you move or need to transport your C 658, this is the safest container in which to do so. We’ve seen too many otherwise perfect components damaged in transit for lack of a proper shipping carton so, please: Save that box!

CHOOSING A LOCATION

Choose a location that is well ventilated (with at least several inches to both sides and behind), and that will provide a clear line of sight, within 25 feet / 8 meters, between the C 658’s front panel and your primary

listening/viewing position—this will ensure reliable infrared remote control communications. The C 658 generates a modest amount of heat, but nothing that should trouble adjacent components.

RESTORING C 658 TO FACTORY DEFAULT SETTINGS

Press and hold both front panel’s aSOURCE sbuttons until the display shows the following three reset options. Use aor sbuttons to select through the options.

•Factory Reset MCU? : Restore MCU factory default settings only

•Factory Reset BluOS? : Restore BluOS factory default settings only

•Factory Reset All? This will reset both BluOS and MCU: Restore both BluOS and MCU factory default settings

Press [ENTER] to select “Yes” and initiate selected Factory Reset option.

IMPORTANT

Restoring C 658 to factory default settings will delete all applicable configured or saved settings.

QUICK SETUP GUIDE

This simple guide will help you get started with your C 658.

Your C 658 can be connected to your home network via Wired or Wireless connection.

IMPORTANT!

•For wired and wireless connection to be established, ensure that a broadband router that supports Ethernet and/or Wi-Fi standards is setup and available.

•Tablets, smartphones and other applicable devices that support iOS (Apple) or Android operating system can be used as mobile device controller. These devices are not supplied with your C 658.

•Download and install the corresponding “BluOS Controller” App for your device.

•The BluOS App is available as a Mobile App for Android, iOS, Kindle and Desktop App for Windows and OS X Computers.

•Mobile Apps are handled by the respective Application Store of the Mobile devices.

•Desktop Apps are available to download directly from the Bluesound homepage — https://www.bluesound.com

WIRED CONNECTION

Using an Ethernet cable (not supplied), connect one end to C 658’s LAN port and the other end directly to your Wired network or router.

WIRELESS CONNECTION

The process is very easy but slightly differs between iOS (Apple) and Android devices. Follow below instructions for the smartphone or tablet that applies to you. Windows and Mac users please see the instructions under Wireless Manual Setup below.

ANDROID

1Open App. The App may immediately prompt you saying “New Players detected”, select ”Setup Now”.

a If you are not prompted, open the Player Drawer by pressing the Home icon in the top right corner of the App.

b Scroll to the bottom and select ”Add a Player” to launch the Easy Setup Wizard.

c Select your C 658’s unique network ID* from the Players detected Window.

d Select your Home Wi-Fi Network from the “Choose a Wi-Fi Network” drop down menu.

e If your Home Wi-Fi Network does not appear or is hidden, select ”Manual SSID Entry”. Enter network or applicable wireless network name.

f Select the “Network Security” your network uses.

2Enter your home network’s Wi-Fi Password in the field provided and select “OK”.

3Enter the “Player Name” you prefer your C 658 to be customized for easier identification in the Player Drawer. Network setup connection proceeds automatically.

4Network setup connection is completed when “All Done!” is shown in the App.

* The C 658’s unique network ID is listed as the product name (i.e. C658) immediately followed by the last four digits in the MAC (Machine Access Control) address (example: C658-001A). The full 12-digit MAC address is printed on a sticker on the C 658 rear panel.

iOS

1Open App. Select Home icon in the top right corner of the App.

2Scroll to the bottom and select ”Add a Player” to launch the Easy Setup Wizard.

3As illustrated, press the Home button and open the iOS Settings App to select the Wi-Fi network you will connect.

4From the same iOS Settings App, select your C 658’s unique network ID*. Follow prompt instructions.

5Return to BluOS App upon completion of the network setup connection.

If the above method does not work or if you are on a Windows PC or Apple Mac, Wireless Manual Setup can be undertaken.

WIRELESS MANUAL SETUP

1Select your C 658’s unique network ID* from the Wi-Fi Setup connection settings menu of your tablet, smart phone or computer and join it.

2“…Control Panel” menu window should automatically open. If not, open the web browser of your device and visit http://10.1.2.3.

3Select “Configure Wi-Fi” from the “…Control Panel” menu. Select your network or applicable wireless network name (SSID) from the “Configure Wireless” drop down menu.

4Enter your network’s Wireless Password (Passphrase, WEP/WAP key as applicable) in the field “Enter password or key (if protected)”.

5Select a “Player name” from the drop down list or use the on-screen keyboard to create a customized room name in the field “Custom name”.

6Select “Update” to save all your settings and complete the set up connection of your C 658. Do not forget to go back to the Wi-Fi Settings section of your device to confirm that it is reconnected to the correct Wi-Fi network.

Your C 658 is now connected to your Wi-Fi network and ready to be used with the BluOS controller App.

IMPORTANT!

Always ensure that your C 658 is updated with the latest firmware. Go to the C 658 product page at nadelectronics.com for firmware update information.